Build number……. Well, a lot. TLB Tele bass

Andyxlh

Well-known member
Build number……. Well, a lot. TLB Tele bass

It has been a busy lockdown, almost one guitar a month!!! So, now I have 4 to fettle with and complete. I couldn’t resist the TLB kit on special offer, so here is another!
Anyhow, bought a nice single coil pickup and asked for a set of lefty tuners.
Plans…
Cut a left hand headstock
Work out what to do with the 3 way switch in the control plate - suggestions? I do have a spare musicman style humbucker I could rout in, but I have a real musicman, lovely to play not 100% on the sound so I think probably not. With a single coil, anything else I could do?
We are about to come out of lockdown so I’m expecting the building to slow!!!
 
Do some filling in, rear routing and do a Dusty Hill tribute bass?

preview.jpg

http://www.fendercustomshop.com/ser...ature-precision-bass-maple-fingerboard-black/
 
That’s a possibility, but it’s a precision body… but close.
Nice idea
Anyone played one of those pickups? No idea what they sound like?
 
Oh yes, now that really hits the spot. That is perfect, just with the upside down headstock too. Damn, that looks cool, not so sure about Frank's drum kit tho'.
I could cut the existing tele plate down and fill the hole too. I guess there is no real use for the 3 way with one single coil?!
 
I've suggested doing a Fender Esquire style control system in the past, just to use the switch. This gives volume control only, volume and tone, and volume + fixed capacitor for a fixed very bassy sound.

If you had a humbucker or mini-humbucker, you could use it for series/parallel/split operation.

Untitled.jpg

Though I'd probably use a 500k volume pot with a humbucker.
 
Nice idea!
It is either that or fill the hole and cut down the plate
Just doing some prelim measurements for the headstock. I made a template of the frankenbass to use for this. The paddle isn’t the right shape for a standard fender headstock, it is symmetrical so for 2 per side, but I think I can squeeze an upside down Tele headstock just
7265516C-B402-4476-9394-0D9FA98AB2A8.jpeg
 
Cool project. Have you got the beard to match?

"It is either that or fill the hole and cut down the plate". Or a larger pick guard to cover the hole!
 
Cool project. Have you got the beard to match?

Thanks! I think it will be fun, a nice foil for the frankenbass project.
No beard, not sure I could even if I wanted to……
I’m thinking the heavy relic look zz top favoured would look cool, there’s hardly any paint left on the timber
Could cut the plate along this line…
99A14DFC-F8EB-4186-BAE3-9E372815E5C1.jpeg
 
I am also part way through a tele bass build. I asked Simon the same question regarding the switch with the single coil pickup. I shall be watching your build diary with interest. Good luck
 
I am also part way through a tele bass build. I asked Simon the same question regarding the switch with the single coil pickup. I shall be watching your build diary with interest. Good luck

It's a good use for the switch, but I tend to thrash about when playing live so the less controls for me to mess with the better - I was considering going to a volume only, but I'm guessing that the single coil might need a live tone tweak.
I'm leaning towards cutting the control plate with a grinder along that line, saving the chrome plating and just gently finishing the edge, then making a small timber insert for the hole to shorten it, allowing the cables to pass under this insert. that's today's idea anyway.
BBF490D2-ED10-403F-BE35-FA27D1597022.jpeg
For finish, I'm tempted to stain the body black japan, sand most of it off leaving it in what little grain the basswood has, thin coat of enamel matte white followed by the red I had left over from the Frankenbass.
Then an argument with my plumber's torch, 80 grit paper, thinned-down oak Feast-Watson timber stain to knock back the red to a maroon and give the timber an aged yellow glow and finally a few generous coats of satin poly clear to seal it in and give the basswood a bit more hardness. Thoughts :)?
 
Last edited:
It's a good use for the switch, but I tend to thrash about when playing live so the less controls for me to mess with the better - I was considering going to a volume only, but I'm guessing that the single coil might need a live tone tweak.
I'm leaning towards cutting the control plate with a grinder along that line, saving the chrome plating and just gently finishing the edge, then making a small timber insert for the hole to shorten it, allowing the cables to pass under this insert. that's today's idea anyway.
View attachment 41861
For finish, I'm tempted to stain the body black japan, sand most of it off leaving it in what little grain the basswood has, thin coat of enamel matte white followed by the red I had left over from the Frankenbass.
Then an argument with my plumber's torch, 80 grit paper, thinned-down oak Feast-Watson timber stain to knock back the red to a maroon and give the timber an aged yellow glow and finally a few generous coats of satin poly clear to seal it in and give the basswood a bit more hardness. Thoughts :)?

I gave mine one coat of black stain, sanded back, then two coats of a purple stain i had, it came up nice. The basswood wasn't all that bad. Then i used 10 coats of penetrating guitar oil worked in with 1500 wet and dry on the last 4-5 coats and it's like glass now, but still a bit satin. I'm unsure if i should add more high build oil to make it more gloss. Il see.
 
That sounds nice! did it strengthen the surface of the basswood too? it seems really soft, but when hit with a decent amount of poly clear it really soaks in and makes the surface harder I find
 
Back
Top