Bass hissing and humming bad and diagram question HELP!

crusaderL0L

New member
So my bass guitar is humming, hissing etc. When i activate rhythm its really quiet and solo is loud, it doesnt seem lile the volume knobs seem to do much of anything, i thought someone outta check it out, im resoldering the bare wires and this black wire (meant to be soldered together on 1 spot) again without tolangling them together, mayne this oughtta work. Any tips or tricks would be helpful.

Diagram question, the diagram shows thag the bare wires and black need to be soldered together to a spot (bottom right) and im noticing 2 squares there but the diagram well it only shows 1 from my understanding, should i solder both together?
 
10378.jpg
 

Attachments

  • Screenshot_20261029_145643_Gallery.jpg
    Screenshot_20261029_145643_Gallery.jpg
    402.1 KB · Views: 17
Hi Crusader,
Looking at your wiring picture - the bare shield/ground (earth) wires from both pickups and the ground from the jack socket all need to be soldered to the rectangular looking area at the lower left of the board. The hot wires from the pickups look good, and the hot wire from the jack socket looks good.

After soldering the bare wires, I would add some electrical tape (or heat shrink before soldering) to ensure the bare wires do not touch anything on the back of the board - that may have been creating a short and hiss sound!!

Was the jack ground soldered onto the rectangle shape prewired?
 
The bare wire from the jack socket would join with the other bare wires from the pups. Twist them together and solder all three onto the lower left rectangular tab.
 
I have not done this build but -

I would not expect the rhythm to be very quite!
I would expect the volumes to work like normal.
I would have thought the bass and treble switches affect the tone only!

If they do not, there must be something wrong!
 
I have not done this build but -

I would not expect the rhythm to be very quite!
I would expect the volumes to work like normal.
I would have thought the bass and treble switches affect the tone only!

If they do not, there must be something wrong!
I just tried them out with heasphones, and i searched them up they seem to be how they intent too. Im noticing that when i press on one od the pickups with my the humming backs down alot, usually the bridge pickup mostly
 
I just tried them out with heasphones, and i searched them up they seem to be how they intent too. Im noticing that when i press on one od the pickups with my the humming backs down alot, usually the bridge pickup mostly
Also i soldered the grounds wires but it seems to be still hwaps of humming and hiss
 
Another thought - Is there a ground wire from the Tailpiece to the electronics? The strings need to be ground!

I know it is not shown on the wiring diagram - but I'm sure it needs one. Not having one could explain the hum. And why the hum is reduced when you touch the pickup.

I'm sure a wire needs to run from the tailpiece, where it connects to the body, through the inside of the body, and be soldered to the other ground wires. The ground wire should have bare (splayed out) wire pressed between the tailpiece and body as the bridge is screw onto the body (or between the body and the lower strap button!). You may need to drill a hole for this ground wire, between the tailpiece screw holes, leading into the body. It may need to be a deep hole as there is a thick block of wood in this part of the body. There should now be 4 ground wires (2 pups, jack and tailpiece) soldered to the ground on the board. (I hope this makes sense!)

Also note that on the control board the "step" tab next to the bridge hot wire is also the ground (thus it has the three holes for connecting the three grounds!!!). The other tab I called ground is probably for the prewired jack ground. NOTE: This will not affect the sound as they are all linked together anyway.

ground wires tab.jpg
 
Can you post a pic of your control plate (the front side where the switches are labled)?

On a traditional Beetle bass, the "Treble" switch turns the bridge pickup on and off. The "bass" switch turns the neck pickkup on and off. The Rhythm/Solo switch is a filter...sort of like a tone control, but on a switch.

In other words, instead of a three way pickup selector switch, these basses have two on-off switches for the pickups.

You do need to ground the strings, as TD says, which may be a source of the hiss. But since the bridge is made of wood on these basses you need to ground it at the tailpice. You do it the same way you would do a bridge, but under the tailpiece here:

1793291193129.png
 
On closer examination, I am not surprised you are confused. Me too! I feel most confident that the white-from-yellow wire is connected properly. I think the white-from-red wire is also correct.

If you have a multi-meter, use the ohms setting to check continutity. Clip one lead from the meter to the ring of the jack. With the other lead from the meter check the two places where TD thinks the ground is. A am guessing that the black wire goes to the jack. If so, the braded-from-black wire should also be contiguous with the ring (grounded).

The white-from-black wire should be the hot lead out of the circuit board. This wire should NOT be grounded. It may not matter, but I think the two spots where I put the double-headed yellow arrow should also be contiguous.

1793302187046.png

You need to attach the braded-from-yellow and braded-from-red to a grounded terminal...so any of the three in the stepped ground should do. Third was probably intended for the tailpiece wire.

It's confusing that the diagram does not show where the jack wires are supposed to attach...nor what is on the other side of the PCB board. We know that what's attached at least two pots and three DPDT two way switches.... You can see where their solder terminals are on this side of the board, but it would be nice to know how they are wired together on the other side!
 
Went bak through some old threads... I am more confident what we ID'd as grounds are in fact grounds. I also think the terminal that I labled with a red arrow and "G" is also a ground. Worth checking, anyway! Also more confident that were I put the green arrow is the "hot out."

Not confident that what I circled is a ground... It may be, but I am not sure. I am sure, however, that the braded-from-black wire needs to be attached to a ground. I have seen it attached where I put the other red arrow on historical builds that at least *look* like they are using the same circuit board.

1793306873675.png
 
I have also done a bit more research:
The shielding from the yellow wire pickup should be connected to the blank tab on the top right of the board - so that the yellow pups hot and ground are next to each other.

The ground from the jack socket (the black wires ground) should be soldered onto the rectangular ground tab next to the jack wires hot wire - this must have come off as it should be prewired!

The shielding from the red wire should go on the "step-shaped" tab on the bottom left of the picture.

The string ground, from the tailpiece should also go to the "step" tab.

In the end all the grounds are connected - so it does not matter as long as the ground wires are all to ground!! Using the intended ones will make the wiring neater and also have less chance of short circuits.


I have informed Tim from PBG about this and will try to get the wiring diagram fixed.
 
Back
Top