Gavs ESB-4 Hollowbody Bass

gavinturner

Well-known member
hi guys,

Finally my ES335 Hollowbody Bass kit has arrived and it's a beauty. When I first queried Adam about the possibility to produce this as a kit, I didn't hold out much hope of it coming together. Nowhere else on the internet, either here in Oz or overseas can such a kit be found. But Adam came through thanks to the support of the bass building enthusiasts here in the Pitbull community. I owe a debt of thanks to everyone who helped make this a reality by supporting the kit with a pre-order. It's always a bit of a gamble with new kits - it usually takes a couple of rounds to iron out the small teething problems - so I'm really, really thankful that the guys in this remarkable community stepped up and enthusiastically supported it.

Anyway, enough gushing - on to the kit! The body is really beautiful, with a pronounced flame maple figure that will look great with the planned cherry dye with black highlights.

55k30-fitted-back.JPG


33878-fitted-above.JPG


I have similar issues with the tuners on the headstock not fitting that Bassguy and Tim have previously reported, and I'm not sure what I'm going to do about it at this stage. My current thinking is that I'll have to fill the holes with dowel and re-drill for smaller tuners. Hmm, depends how brave I am feeling.

6j3hj-tuners.JPG


I'm really itching to get started on this one. Checking the neck fit will be the next job while I mull over the required fixes to the headstock.

cheers,
Gav.
 
Its a shame the head gear doesnt fit ,
I am looking at doweling the holes and redrilling with smaller tuners to.
Looking forward to seeing how yours comes together.
 
Your right again Gav. I had to use conversion bushings on my LP, so I could fit the older style klusson tuners.
If my memory serves me correctly, the klusson had a 6mm peg and these kits have a 10mm hole.
They worked a treat.
 
I doubt the bushing idea will solve my problem. The holes are so close that my tuners are touching each other. If I dowel to spread them apart I would have to trim the housing of the tuners. Not ideal.

Small tuners for me is the answer, but no loss- I have another bass in need of new 2+2 tuners....
 
Ok guys I need some serious help here.

Closer inspection of the neck heel fit shows some serious issues with the woodworking in the neck pocket. The interior bottom surface of the pocket is very uneven and to my amateur eye does not seem to be finished deeply enough. Here's what i mean.

There are several "steps" in the pocket base surface, where the surface has not been completely levelled. It may not be completely visible in the photo:

94ufo-neck_pocket_closeup.jpg


These steps lead to a big gap where the neck meets the edge of the body as the neck heel is not seated squarely on the base of the pocket:

xrfh1-neck_pocket_fit_1.jpg


It also shows a gap in the neck profile where the end of the fretboard meets the front of the bass. Looks to me like the pocket isn't quite deep enough. Maybe the factory didn't get around to finishing the pocket??

1c577-neck_height_profile.jpg


The real question is how can I rectify this? I'm a bit out of my depth here, so any suggestions are greatly appreciated.

thanks guys!

cheers,
Gav.
 
Looks like a question for DB or Gav. My suggestion would be to first check what your neck angle is like with the neck 'seated' as best as you can and the bridge sitting in place, with regard to action etc. That should give you an idea of what options you have and help to guide you on how to proceed.
 
Envious! That's the kit I would have loved to build, but knew my limited skills I should start with something simpler... Seeing your issues makes me think I definitely made the right the right choice, but I certainly hope you can sort out them out and make it into something brilliant. I'll be watching your progress with great interest! :-)
 
John / Gav - these kits do seem to have some variation in them - tried getting all my tuners in and they seem to be a snug, but comfy fit. I'll check the neck seating on mine and see how it looks.
 
Hi Gav,

If you have a router and a neck pocket jig/template this would work best. If not, i think that you might need to file the pocket down that 1mm or therabouts to get it as level as you can.
 
Thanks Gav, unfortunately no router or templates, but I do have a bastard file that might serve. Will probably be ok if i take small steps and test often. Will also take Scott's advice about an initial action test with the current height.

cheers,
Gav.
 
hi guys,

Filed out the neck pocket today with my bastard file. Just flattened it out a bit little by little. The height at the end of the fretboard has come down a bit and the neck is sitting much better in the pocket. There is a little gap at the heel, but not enough for me to worry about. I may fill it with Timbermate once the neck is on, or I may go back for a little more filing. Not sure.

zzx26-neck_alignment.jpg


amjn6-neck_alignment_2.jpg


hi4tn-neck_fit_after.jpg


Anyway, I'm much relieved. The neck alignment was good straight out of the box and even with the neck lowered into the pocket the strings are still flat on the deck at zero bridge height. Now I can stop worrying about the fit!

cheers,
Gav.
 
Looking pretty snug in there Gav and should be OK with a bit of spakfilla ;-)
This'll be a nice brother to the florentine I reckon.
 
hi guys,

This morning I took the plunge and attempted my second ever burst using ColorTone dye - a so called "poor man's burst". I prepared the body with a light sand down of 360, 400 and 600 grits. At 600 grit I did a single pass of grain raising using Metholated Spirits, but the maple hardly needed it.

This time around I didn't perform a 'trace-dye' on the wood to check for glue spots. I was instead prepared to stop dying if any glue surfaced and perform a sand back to remove it. Amazingly, this kit exhibited no glue spots at all around the binding or veneer join. The quality of this kit is awesome!

I performed the burst using ColorTone Vintage Amber as a base, and then applying ColorTone Red Mahogany around the edges. I was Also going to darken the edges even more with a few drops of Tobacco Brown, but I like it now and don't want to muck with it.

kbwn2-burst_small.JPG


Gotta say I'm pretty damn pleased with it. The edges are nice and dark with the red mahogany bleeding into the flame maple as it reaches for the centre of the guitar. The centre has retained it's bright Amber hue and has not been muddied with brown. All in all a pretty awesome result - I'm right chuffed with myself. Now on to the back and sides!

cheers,
Gav.
 
As a postscript to my previous post.. I just took the masking off the binding and it's as clean as. The magic 471 pin-striping tape from 3M does it again!!

3ai0r-burst_small_binding.JPG


cheers,
Gav.
 
Noice, very noice!
Looks like you lucked out with the neck fit/ angle.... I had to shim mine at the butt end of the heel to get the neck sitting at the correct angle, and to get a nice flat action...
 
looks excellent Gav, for a 2nd burst you must be stoked ! Look forward to seeing this beast progress. Remember to psyche yourself up for the wiring !
 
Back
Top