Dual Build: GSJ-1 and GSM-1

Simon Barden

Well-known member
I'll be building these two SG style kits, an GSM-1 and a GSJ-1 together and in parallel with identical finishes, so there didn't seem any point doing two build diaries. The GSM-1 is for me, and the GSJ-1 for a friend.

The kits have just arrived today (I forgot they were coming so it was a nice surprise!).

GSM-1:

The kit looks lovely. I have been lucky and scored a one-piece body. It's also pretty light. The neck is nice and straight. The neck is a very tight fit in the pocket, but this fit should relax after a few days acclimatising

GSM-1 body:
g5Bx7i.jpg


GSM-1 body and neck:
qzZb0i.jpg


GSM-1 rear view. The factory look like they are in dire need of some sharper drill bits, but it's nothing that can't be patched up and any repairs will be hidden under copper shielding tape anyway.
yGgSU8.jpg


GSJ-1:

This is a two piece body, but made from very similar pieces of mahogany. Again, the neck is a real squeeze to fit in the pocket, but should fit better in a week or so.

I had a look at the P-90 and it appears to be of a different construction to the one supplied with BlindDrew's ES5-V, as it has the proper dog-eared backing plate for fixing the bobbin, rather than it being of a soapbar-type construction with the bobbin being stuck to the plastic cover. But the two bar magnets used are definitely shorter than standard. I suppose magnets are relatively expensive,even ceramic ones, and if you can make 10 pickups from a ceramic bar that would normally make 9, then it's all money saved.

GSJ-1 body:
wHZk2v.jpg


GSJ-1 Body and neck:
dNmCn4.jpg


GSJ-1: Body join. The back of the body looks fine, but there is a slight glue line at the rear of the top where the two halves of the body weren't quite cut square to each other. No crack in the finish as such, as it's filled with glue. Obviously it would be nicer if it wasn't there but I can live with it. Going Heritage Cherry for the finish on both guitars, and as well as a red stain, I'll be using some Heritage Cherry nitro lacquer on it before the clear coats are applied, so that should hide most of that.
Ge4jtY.jpg


There's also a small annoying ding in the top that's been filled with mahogany-coloured filler. But it's not that big and it should be near-invisible once finished.
ZC2q5G.jpg


Got a couple of other projects on the go as well, but we've got a spell of good weather, and my plan is to get them all ready for spraying at the same time.
 
I've been doing some initial tidying work whilst waiting for the body woods to settle and acclimatise.

Tidied up the control cavities and enlarging the pot holes to fit CTS pots. Glued some of the splintered wood back in place.

I removed the two plastic nuts, ready for bone replacements. One (the GSM) was definitely fitted with a gap between it and the end of the fingerboard and I found out why:

4VDkV6.jpg


You can clearly see a metal pin sticking out of the end. These are used to hold the fretboard in place whilst its glued and clamped to the neck, but it really shouldn't have been fitted so close to the end of the board. It was sticking out quite a bit and prevented the nut from fitting against the end of the fretboard. A few moments with a Dremel and a grinding wheel and it was gone.

Then I removed the nut from the GSJ, and what did I find?

L19LUg.jpg


Yes, a very small part of another pin in exactly the same place, which was preventing the replacement nut from sitting quite flush. So a bit more grinding to fix that.
 
Marked up the headstocks after tracing an outline from a LP.

Here's the SG Jr after initial excess wood removal prior to going in with the Dremel drum sander and sandpaper:
5OmcEZ.jpg


And here's both the Jr (L) and SG (R) completed:
gqcj2L.jpg


I discovered that the shaping on my LP isn't quite symmetrical, so neither are my shapes. That's hand-built for you!
 
Marked up the headstocks after tracing an outline from a LP.

Here's the SG Jr after initial excess wood removal prior to going in with the Dremel drum sander and sandpaper:
5OmcEZ.jpg


And here's both the Jr (L) and SG (R) completed:
gqcj2L.jpg


I discovered that the shaping on my LP isn't quite symmetrical, so neither are my shapes. That's hand-built for you!
Awesome, they are both going to have a story to tell. Hand built for the win.
 
The latter part of yesterday and this morning were spent sanding down the bodies and necks. The neck heel start quite a way from the body, so I reshaped the necks to give a more gradual transition and easier upper fret access. I used a drum sander on a Dremel to increase the size and sharpness of the edge bevels, after which it was all sanding the bodies down again. So they are all ready for grain filling. It turned rather windy and cold outside by lunchtime, so I didn't do any more today.

Plus, I have some very sore back muscles at present and I overdid it by working all day yesterday, so much so that I could only get comfortable by lying down. So today, I went a bit easier on the bending over etc.

Yesterday I tested out staining the clear grain filler I'm using (Aqua Coat), with some dark red stain, and tried stained and unstained filler on the headstock offcuts, just to see how it compared, and whether I could then use my heritage cherry stain over the top once it had been sanded back. Both fillers worked OK, with the stained one having a bit more interest in the finish because of the darker colour of the filled pores. So stained grain filler it will be. So tomorrow, it will be on with the rubber gloves!
 
So today is grain fill day.

Mixed up some stained AquaClear grain filler and sloped it on. I did have pictures of the grain filled necks but managed to delete them.


The GSJ-1:
s67gDK.jpg


The GSM-1:
XVLlSr.jpg


Still got the back to do in about an hour's time when they should be dry enough to turn over. Don't need to be too careful as most of this will be sanded off again. Just don't want the bodies sticking to the cardboard!
 
Looking good Simon. Nice tidy work.

re: AquaClear, how much do reckon you use on one body?

It's available here in AUS now from one supplier but it's $55 for a US pint. (473ml for us guys)

It would be worth it if I could get 4 guitars out of it, but then there's probably shelf-life to consider as well. Would hate to have to throw it out after 1 build.

Cheers
 
Scored with that one piece body, these are going to be nice.

What ever happened to those semi hollows you were working on? Don't recall seeing them finished.
 
Semis are still going. Neck of one is with JimC, and lockdown makes it awkward/expensive to get back. Mainly finish to do, and it's still a bit on the cold/windy side for spraying outside.

I have the one US pint Aqua Clear container, and it's done a bass (twice because I messed up the first time), a Strat body and these two kits so far. Still enough left to do at least another guitar. £31 here, so roughly the same cost.
 
I decided to buy an LCR tester to help me compare pickups.

So I tried it on the GSJ-1's P-90 pickup and compared it against the Creaery P90s I've got for my ES-1/ES330 build.

I had a feeling that the kit P-90 would be a bit of a bruiser, but I was wrong.

The Creamery bridge pickup measured:
DCR 8.52 kohms
Capacitance 16.6nF
Inductance 7.07H

Whilst the kit P90 measured:
DCR 6.86 kohms
Capacitance 23.2nF
Inductance 3.49H

I used another pickup magnet to compare magnetic pull/resistance between the two pickups and they both seemed very similar. As I know the Creamery P-90 has Alnico 2 magnets, then I can only assume that the kit P-90 either has Alnico 2 or 4 magnets, and not ceramic ones, which are much more powerful.

Which leaves me wondering why the inductance of the Creamery is so much more than the kit pup. Assuming they both have 42AWG wire, the kit pup obviously has less turns, but using the ratios of the DCRs to multiply the inductance of the kit pup, that still only gets me to 4.3H, 2.7H short. So maybe the kit pup has 43AWG wire, and even less turns than the DCR suggests? Or maybe it's down to different magnet strengths that my very basic test isn't showing. The kit pup magnets are definitely both shorter than the Creamery ones, which would explain some of it.

I was thinking that the difference in capacitance was down to the Creamery one being hand wound, compared to a more regular machine wound winding of the kit pup. But it may also be down to different wire insulation as well.

One thing I did notice on both kits is that the supplied truss-rod covers are 2-screw standard Gibson types, whilst the kit needs the 3-screw type. Luckily I have a stock of G-style 3-hole truss rod covers!
 
Thanks for the info on the AquaClear Simon.

Interesting info from the LCR readings too.
Just curious if you've played/heard the two pickups, and if there is a noticeable difference in tone between them?

My understanding, from a very general perspective, is that lower inductance favours higher frequencies, and higher inductance, lower frequencies. (effectively determining resonant peak)
Do you find this to be the case with those two pickups, with the Creamery being twice the H?

Cheers
 
Never heard them yet I'm afraid. The Creamerys are for my yet to be completed ES-1/330, and the PBG P-90 is for the GSJ-1 that's one of these builds.

Certainly more inductance moves the resonant peak down the frequency range, so more mids and less highs, and also contributes to more output (along with the number of turns of wire). The capacitance also has an affect on the sound, as more capacitance = less treble, and affects size of the resonant peak.

I also measured the two kit humbuckers that came with the GSM-1, and they has less capacitance, and only slightly more inductance, than the kit P-90 (but a lot higher DCR at 11.89k (B) and 11.64k (N) ). But they only use one magnet, unlike a P-90 which has two, so you lose magnetic inductance but gain it back from having two coils with more total turns of wire. And despite having two coils, the capacitance is only slightly higher, presumably because the coils are physically smaller so less distance between the innermost and outermost winds on each coil.

Sanded the grain filler off the bodies so far today (2.30pm-ish here) and am halfway through one neck. Hopefully I'll finish sanding in time to stain them today. Just checking the computer to give my arms a rest!
 
Finished sandinng the excess grain filler off, then stained the bodies and necks. Kept finding sanding scratches that needed more sanding after I stained the bodies, and still have a couple of areas that really need a bit more work on. Should just have enough stain to do it, but there's not that much left in the bottle.

About 10 hours solid work on the guitars today, and I'm really tired, so will edit and post a few pics tomorrow.

Next step is the headstock veneers with black fibreboard and some abalone inlay.
 
The kit pup magnets are definitely both shorter than the Creamery ones, which would explain some of it.

Not sure if it’s still the case with these Junior kits, but the one that I built had a smaller pickup cavity to suit the kit pickup. The base plate of the pickup I swapped it out for wouldn’t fit in the cavity. It may pay to future proof & enlarge the cavity now before finishing.
 
Curious what you stained with? It looks like you are going with a fairly faithful build on the colors anyway. The lead guitarist in my band in high school had an SG that color. It's always been my favorite electric guitar. This will be fun to watch.
 
Back
Top