Daves SG Build Whist Waiting for the clear to dry on my LP

DaveC64

Member
I cant hang around waiting for the paint to dry so on to my next build.
I am in two minds may be four for the finish. I found this finish on the internet.
65px-SG-supreme.jpgimages.jpg
But I really like solid black bazecoat with a tiny amount of pearl in it. Less than my Les Paul. similar to this one.
2016_USA_Style-SG-banners-740x280.jpg
Or do I go radical with Holgrafix paint.
HGX-Body.jpg
Or if I get bored with the black bazecoat I could spray over it with black chrome in a year or so when it cured.
I do not know what the Mahogany is like yet for option 1 I will have to wait and see hopefully it will arrive tomorrow.
The first option looks like more of a challenge but I would need lots of trips to the paint shop to get the right colours.
What say ye all.
 
Last edited:
Tend to think that if the body has good grain it deserves a stain finish. Solid colour if the timber is just plain jane.
 
How about like this but with darker edges. Of course only if the grain is good. What stain is compatible with 2k acryl
SGS18AMCH1_MAIN_HERO_01.jpg
 
Last edited:
That looks nice.

No idea what exact colour is but suspect a combination of some gold in the middle and a brown outer. Dingo Tone Coolangatta Gold & Nullabor Ochre or Feast Watson Golden Teak with Teak Brown or Oak.

Never used acrylic so cannot comment on that aspect.
 
I did a test on plywood to see if acrylic would stick to my stain. I also used the same test to see what the stain would look like.
 
I have ordered a six pack of assorted 250ml water based coloured stains off ebay. cheaper than buying singles. I will have to experiment on some ply to check out the colour that I am looking for hopefully it is a nice piece of log. If Australia post can work out how to send a parcel to the correct address on the label I may see my sg today. Its done more gigs than me already.
 
I have ordered a six pack of assorted 250ml water based coloured stains off ebay. cheaper than buying singles. I will have to experiment on some ply to check out the colour that I am looking for hopefully it is a nice piece of log. If Australia post can work out how to send a parcel to the correct address on the label I may see my sg today. Its done more gigs than me already.
Did you buy a 6 pack of Ubeat dyes?

Sent from my SM-A520F using Tapatalk
 
Finally it has arrived it is 2 distinct planks. I will try to get the lighter plank darker before I Apply any stain on top.
IMG_20171026_105002.jpgIMG_20171026_105037.jpg
 
Last edited:
I have ordered the U Beaut dyes and the U Beaut Sanding Sealer 500ml.
I should have used that on my LP I did have a few issues with grain rising at the grey primer stage.
I especially like the bit where the sealer will stop the grain ends absorbing lots of dye and going really dark.
Wish My uncle was still alive he was a professional french polisher. The last time I worked with mahogany was when I made a coffee table at school I used wax to polish and finish the wood. It is too long ago to remember the process. I know I had to use assorted veneers on the table top because a mahogany top would have been beyond the school budget.
Any way thanks for the advice guys now the work can soon begin.

The winner is
SGS18AMCH1_MAIN_HERO_01.jpg
 
Last edited:
I have spent a couple of hours sanding by hand whilst waiting for the sealer to arrive. This mahogany is as hard as I remember. Now I have it sanded to a good finish it has some fine what look like very fine band saw lines on the front almost like coarse sand paper grooves. If they do not sand out they could be an issue when I start on the dye. they could leave dark straight diagonal lines. I don't want to have to get the power sander out.
 
I have spent a couple of hours sanding by hand whilst waiting for the sealer to arrive. This mahogany is as hard as I remember. Now I have it sanded to a good finish it has some fine what look like very fine band saw lines on the front almost like coarse sand paper grooves. If they do not sand out they could be an issue when I start on the dye. they could leave dark straight diagonal lines. I don't want to have to get the power sander out.
Sometimes you need to sand in the same direction as the machine marks and once they are gone revert back to sanding in direction of the grain.

Sent from my SM-A520F using Tapatalk
 
Sometimes you need to sand in the same direction as the machine marks and once they are gone revert back to sanding in direction of the grain.

Yep I tried that but the wood is so dam hard it is hard to make in impression hence I have used some sealer in hope that it will help with my next sanding pass.
 
Back
Top