Wokkas scratch tasmanian blackwood build

wokkaboy

Well-known member
Hi all,
was lucky enough to go and see Dingobass ran me through building a neck from scratch on Friday, I learnt so much and know now what tools and materials I need (thanks heaps DB by the way). Wish I took some photos of the neck building process. I've had a body blank of tasmanian blackwood for a few months and have been waiting for a neck. I didn't know what body shape I was going to cut so left the headstock a paddle shape.
The photos are after I've roughly shaped the back of the neck and drilled paua shell fret dot markers. The body shown is a spare strat body
8ry26-2014-04-12-00.18.41.jpg

79v5m-2014-04-12-00.19.06.jpg

6y366-2014-04-12-00.20.29.jpg
 
I chose an Ibanez body shape as I've never built an axe of this shape, so modelled it on the shape of an Ibanez S series axe I have. First routed the neck pocket while there is meat on the blank for the template to rest on.
Then traced the body shape and in true 4D style made the horns longer.
This neck has the truss rod at the heel end so had to route out a small pocket for this to fit south of the neck pocket.
Then cut the shape on the bandsaw. After seeing DB's bandsaw on Friday I realised we have had our upper bearing guide for the blade way too high causing the blade to wander cutting harder woods. We lowered it and its cutting heaps better now, could cut curves with a thick blade
84ys5-2014-04-12-16.25.48.jpg

46v39-2014-04-12-17.08.42.jpg

x3f84-2014-04-12-19.11.38.jpg
 
I wasn't sure whether to cut a 3+3 headstock or 6 a side but decided to keep it a similar shape so went a fatter style Ibanez shape. Next to it is the S series I modelled the shape on
gk111-2014-04-13-20.58.24.jpg

p04ph-2014-04-13-21.02.54.jpg

84dfa-2014-04-13-20.57.17.jpg
 
cheers Pablo, I never heard of a Mayones Setius, just google imaged it and came up with an idea how it could look.
I was thinking of gold hardware but this picture has almost made the decision for me, think black hardware is the go. Still not sure whether I'll fit a floyd rose or cheat with a strat style tremelo. Bit nervous about setting up a floyd and the cost of them !
5j2li-mayones-setius-pro-lizard-side.jpg
 
@ Jarrod --> cheers mate
@ Pablo --> cool I might look into this wilkinson tremelo looks much simpler than a Floyd setup
 
cheers Stan, I recommend these Pit Bull body blanks, I'll be trying another type next, the grain is awesome and the shavings are such a rich chocolate colour I don't think I'll be staining the body much
 
Look out. There will be no stopping you now your starting to make your own necks. What woods did you use for the neck?

I'll second the point on the PBG body blanks, awesome quality and value for money.
 
cheers Dan. The neck is rock maple (think it was queensland rock maple) and the fingerboard is the same wood as the body, tasmanian blackwood. I'm thinking about a blackwood veneer for the headstock too, got enough offcuts from the body blank
 
thanks for the comments Robin and Haydn.
I've ordered some black hardware for it today, need to order pups and a switch next.
 
/<\\/p>[]<\\/p>/Quote from wokkaboy on April 14, 2014, 12:17
@ Jarrod --> cheers mate
@ Pablo --> cool I might look into this wilkinson tremelo looks much simpler than a Floyd setup


Looking good Woks.

Take a look at the Full Contact Hardware range... Amazing gear and for the quality it is very cost effective.
fullcontacthardware.com

The inventor, Geoff Babicz was with Ned Steinberger in the early days so you know it is going to be good!

I used the Babicz TOM bridge on the Jag Baritone... (its not just Teles that dissapear into Adams collection) ;)
7sj58-IMG_1864.JPG
 
cheers for the suggestions for the bridge DB. Being an ibanez shape I have to go down the Floyd rose road. I've ordered black hardware from a SV1 kit so I'll see how that goes.
I'll give the full contact hardware a try on my next scratch build
 
I got the 2 humbucker cavities routed yesterday, not going to run a middle single pup, keeping it simple. Will be ordering some black buckers for this baby.
On to the floyd rose cavity this arvo, thats going to be a mission but I have a SV1 to model the templates on.
Still got some work to do on the neck, final sanding, thin superglue and fretting, not enough hours in the day and too many other projects on the go !
55069-2014-04-18-17.04.49.jpg

9ad99-2014-04-18-17.31.37.jpg

x9f44-2014-04-19-10.30.19.jpg
 
got the floyd trem recess routed, what a job that was. Had to make two templates and route 3 different levels. I wouldn't have been able to do it without having an SV1 body to get the route shapes and depths. Next floyd trem route will be much easier. Today will route the spring cavity and hopefully control cavity
tlj7n-2014-04-20-00.25.41.jpg

w94ol-2014-04-20-00.28.44.jpg

171dd-2014-04-20-00.31.41.jpg
 
Back
Top