sg mark 2 !!! bulid with bigsby !!! and piezo tuneamatic bridge!!!

  • Thread starter Thread starter Guest
  • Start date Start date
G

Guest

Guest
just scored my next project ,, payed $133 delivered for sg kit ,, bigsby set me back $50 ,, tunematic piezo with preamp $160 , total of $343,, will be setting up with split coil humbuckers (wilkisons) with push pull pots ,, some might remember my last sg make (as in pic) ,, shape will be same but beef up the hardware!!! so looking forward to the end result !!!
s3hc3-20130517_110953.jpg
 
which Bigsby do you have??? you might have to alter the shape to accept it, if you have a B5 you can get a Vibramate V5 to accept it

Either way it will be AWESOME!!!
 
got b5,, going to plug holes with dowel cut from offcuts ,, and will have less cut from arse tho ,, will have flame cut but higher and less from where bigsby will go !!! doing it this way will ensure that holes will be filled with same wood and when painted in a car paint it will not be able to be seen !!! got it all covered !!! PS : you must sit on this forum just waiting to reply to people LOL
 
hahaha nah i was just doing my usual secondly check haha!
Sounds like a good idea, let's wait for the Resident Luthiers to have their say!
 
/<\\/p>[]<\\/p>/Quote from muffbuffer69er on July 10, 2013, 18:33
just scored my next project ,, payed $133 delivered for sg kit ,, bigsby set me back $50 ,, tunematic piezo with preamp $160 , total of $343,, will be setting up with split coil humbuckers (wilkisons) with push pull pots ,, some might remember my last sg make (as in pic) ,, shape will be same but beef up the hardware!!! so looking forward to the end result !!!

Sounds great Corey.

I just hope that one day I will understand half of what you just wrote. Geez, getting old sux. lol

rob
 
Yeah getting older & denser does suck . . .
How does the piezo system tie in with magnetic pickups?
Am I asking a silly question? :?
 
Are you going for a stereo jack or two separate jacks? Ideally you want to send the magnetics to your amp and the piezo to a DI or an acoustic amp.
 
im not sure yet i will see what the pre amp wiring has on it ,,, KIT arrived today very happy with ,, neck a little loss in joint tho, wish they were a little better fitting make setting neck a lot easier ,, will post pic later !!!! ,, have to start marking out the cut outs !!! and shaping head stock !!!!
 
marked out both cut outs ,, drilled out most of the wood ,, then use dremel tool to carve out the wood ,, then with my trusty files and 60 grit norton sandpaper spent 2 hours getting one side perfect ,, will do the other side tomorrow and will be doweling the holes from the stop tail for the bigsby to mount , will post pic when down ,, not to all the curves are all taken from the pickgaurd !!! THATS what i use for the template
 
/<\\/p>[]<\\/p>/Quote from muffbuffer69er on July 19, 2013, 19:22
8-)
all doweled up and cut outs done ,, !!! ,, be doing flames cutouts after sized up bigsby !!!!
3068m-20130720_181853.jpg
 
thinking off adding a p90( in the middle ) ,, have to check my spare parts and wiring off harness with pre amp
 
Looking great! You make it look easy.
I'm inspired to start thinking of possible body shape mods of my own :).

Cheers,
Gavin.
 
so got my head stock marked out and cut out ,, made the same shape as mark 1 sg make !!!!
 
Back
Top