No. 29 is underway. (GPB-4M P Bass Maple f/board.)

ozzbike

Well-known member
Yes No. 28 the Firebird is still getting finished, and No.27 The Seconds Order Explorer is nearly finished....binding issue.

But I have grabbed one of these just for me.

I have ordered the kit from PBG with these extras:-

Entwistle PBXN pickups
Graph Tech TUSQ nut
Sprague 0.047uf capacitor
Switchcraft 1/4inch jack socket
Bourns Audio Taper Mini 250k pot.

And these from Real Parts:-

PB Style pickup chrome cover
PB style Bridge chrome cover
Wilkinson 4 string Bass Bridge
Bourns 250k push-pull pot
Allparts four inline chrome elephant ear tuning machines
Schaller style straplock buttons
Metal Dome Chrome knobs

And from E-Bay

A black plastic Bass guitar Thumb Rest.

All together to make a sister/brother for this Jazz Bass.
 

Attachments

  • ZPBA-4M-00.jpg
    ZPBA-4M-00.jpg
    369.4 KB · Views: 298
  • 1.jpg
    1.jpg
    196.1 KB · Views: 297
Last edited:
But I don't know if I want to colour/dye/stain the body. Or just perhaps use a coloured Timbermate on the grain and then seal it.

Leaning towards the rubbed finish again. The J Bass feels so amazing over 12 months later.

So thinking Feast Watson Fine Buffing oil and then Gillie Stevensons Cabinet Makers Wax to seal it.

But the neck will be one of the few bare Maple necks and fingerboards I have done. I am wondering how oiled and waxed necks and fingerboards handle the strain of regular use from the big strong Bass strings flapping over its surface.

The shade or colour of the finish of the J Bass was set by the use of Walnut Timbermate on the J Bass and then the amber shading over it from the Fine Buffing Oil.

Timbermate comes in a range of colours....

https://www.timbermate.com.au/timbermate.html

I like the idea of the BrushBox, Teak, or Rimu on the Body....and maybe use Rimu, Pine or Oak on the neck and the fingerboard.

Or maybe I should just make a choice and do the whole thing in the same Timbermate and then just seal it up.

I will be cutting the paddle headstock into a P Bass style....I have a multi page template file and I will find which one fits the most of the existing headstock shape....most bang for buck.

I have the wiring diagram from Weirdy from an earlier build and I have the push/pull pot on order and will be putting the parallel/series switching in place.....thanks again Weirdy. :)

Any suggestions for a natural style finish colour scheme? It would be nice to try something different.
 
The body is quite light for Ash and very close to the Maple neck which would lend itself to a vibrant all over stain colour. Translucent Tree Frog Green comes to mind. What do you think?

Sent from my SM-A520F using Tapatalk
 
The body is quite light for Ash and very close to the Maple neck which would lend itself to a vibrant all over stain colour. Translucent Tree Frog Green comes to mind. What do you think?

Sent from my SM-A520F using Tapatalk

Translucent Tree Frog Green....great how your mind works. Funny.

I think enhancing natural colours and those produced by the finish will be the extent of my efforts. Sadly my coloured finishes never end well.

Thinking of doing similar to what I did with the Jazz Bass. Use a coloured timbermate to produce an overall hue on the body....then the Fine Buffing Oil and Cabinet Makers Wax will leave their Amber/honey hue over the top.

I am thinking of trying to get a darker brown colouring in the deep grain with a honey colour on the higher grain. I was also thinking of doing similar on neck and fingerboard. So no bright coloured neck for this one.
 
You can also grab the Natural Tint Base & add just about anything to make your own colour at 4:50 -

https://www.youtube.com/watch?v=gwBbE0PG5tY

This interests me....but will it work with the watered down nature of an all over body fill we use on guitars? The video is colouring the timbermate in putty form. I can assume it will.

I have lots of water based stain colours at home....test and tune time I think.

I want a darker brown down deep in the marked grain....and the higher smoother wood to be a more amber or honey colour. I hope that will look okay.

My concern of using my own mix would be colour matching any repairs.

I may try a colour of timbermate off the shelf I think.
 
Last edited:
The timbermate tale.

Flying green shed visit today.

I now have NATURAL/NEUTRAL tint and Cedar/Blackwood. The colours look way different in the plastic jar.....and even different to the sample board hanging in the green shed.

I think I will do the normal body wash fill with the cedar/Blackwood and sand it back....then make a mix with the neutral tint and some orange to light brown water based stain.....make a thicker custard style paste for a large portion of the body not the edges......sand back again....then make a mix with Amber/yellow water based stain and again in a custard consistency smeared in a small middle section.....sand back again.

Feast Watson Fine Buffing Oil applied with 000 grade steel wool with the grain...only. Left to get tacky....coarse cloth....five to six hours.....soft cloth. Repeat once a day until the finish is the desired tone I seek.

Then seven days to gas off....then Gilly Stevenson’s Cabinet Makers Wax with 0000 steel wool and then buff until achieving the sheen I need.

Well that is the plan.....timbermate and waterbased stain and sanding produced light burst with an Amber/Honey hue on the neck and headstock.
 
Hey Ozzie, I'll be watching this build with interest as I have just got a P-Bass Kit. Been thinking of keeping it pretty natural, but will try and highlight the grain.

Good luck with the build, but as its #29 I guess you've got a pretty good handle on how to do it by now. ;)

rob
 
Hey Ozzie, I'll be watching this build with interest as I have just got a P-Bass Kit. Been thinking of keeping it pretty natural, but will try and highlight the grain.

Good luck with the build, but as its #29 I guess you've got a pretty good handle on how to do it by now. ;)

rob

You would think that...but sadly no. I only do hand applied stains and finishes and getting even reliable colours and or shades has escaped me. My better finishes have been ones where...as in this project...the grain and figure is highlighted by the grain filler and sealed by the top coat. If I have to use colour I often sand through parts in my vigour to finish.

However, I have a few tech items and you also have one of them...Weirdy...and I enjoy soldering and wiring challenges.

Sanding and fitting I don’t mind...applying stains and finishes not bad either....finish sanding...wet sanding....polishing gets me every time.

Oh, 29 is the number of guitars and basses in my possession....made about 25 from kits.

It is a hobby and you will become a victim of G.A.S. (Guitar Acquisition syndrome)
 
Keen to see how the timber mate sessions work out.
Agree that when you take lid off the contents look anything but the colour you expected.

Sent from my SM-A520F using Tapatalk
 
Nice start Ozz. Timbermate is a great grain filler / putty, but not sure as a colour. As always - if possible do a test piece unless you are happy with surprises. Also a good way to test base and topcoat compatibility . This looks great, waiting to see the fine results
 
Home again.

After leaving to go away for work before Easter I finally got home today. Nice to have a friend in the postie parcel truck. Nice safe, dry pile in my garage.

Nice figure on both the body and the neck.....the headstock is lots bigger than I thought.....nice.

Tired now....but shall check it all off in the morning....nice work for a few days off. :)
 
Crappy weather is made for sanding.....done that.

Sadly I now have a collection of different shades of Timbermate...never hurts.

I used the Cedar/Blackwood as a base all over....then the edge in Ebony.....then the middle of both front and back in a colortone vintage amber stained neutral tint timber mate.....then walnut around the edge of the body over the ebony.

The cedar went on and sanded off really nicely at 240 grit. The ebony came off blotchy....hence the later walnut overcoat.

The hand tinted neutral tint (coloured with Vintage Amber) achieved not a lot at all.

The neck and headstock have been shaped to a P Bass American Deluxe template I had....the corner up under the circular end of the headstock....where the shaped bottom edge meets the round end of the headstock.....very hard to do.

The neck and headstock have had a coat of cedar/blackwood timber mate and has been sanded progressively to 240 grit.

Both the body and the neck....fingerboard and all....have had a single coat of Fine Buffing Oil.

The body wood has had some serious bug infestation during its growing years....so weird marks and shapes in the figure....but I like it.

The maple fretboard on the maple neck is really just flat.

A buff of both later this afternoon and leave to hang over night.

Photos tomorrow and then more Fine Buffing Oil.

It is a yellow/amber colour overall.....lighter than my Jazz Bass that was Fine Buffing Oil over two coats of Walnut timber mate.

Not what I was hoping for.....but I like the effect.
 
Some photos.

Arrival pics....
 

Attachments

  • 1.jpg
    1.jpg
    165.6 KB · Views: 179
  • 2.jpg
    2.jpg
    110.5 KB · Views: 168
  • 3.jpg
    3.jpg
    96.6 KB · Views: 164
  • 4.jpg
    4.jpg
    168.7 KB · Views: 167
  • 5.jpg
    5.jpg
    110.4 KB · Views: 170
Back
Top