New Chapter in my life TL-12S SMV

Do I need a grain / sanding filler?


  • Total voters
    13

Benderson

Member
They're here both kits but i will start with this the TL-12S.
I have to admit i was expecting a lilt booklet with instructions, when i realised that ain't happening. I think I s--- my self.
First thing first i need to set up a space to go back & forth from.

oh boy! where to begin.
46011005635_4da0d5a2bf_z.jpg
 
Last edited:
Mmmm, that’s awesome! Lovely pick mate, you may want to consider minimising the pick guard to highlight more of that spalty goodness!
 
Carefully check drilling & routing relationship with the neck.
I had to plug and move all up & left.

20181117_150219.jpg

20181204_134615 - Copy.jpg

20180605_105812.jpg
 
Last edited:
O, Oh think some poo just come out! No pick guard & what pick up is that?? I like.... is there a link on how to check all that??

Don't let it worry you, just take it one slow step at a time.
Neck pickup is a Jazzmaster from Guitar Fetish.
https://www.guitarfetish.com/Jazzmaster-Style-Pickups_c_798.html
I'm sure others can direct you to a link showing exactly how to check neck to routing and how to correct any error. If I don't see any help by this time tomorrow I'll in my long-winded clumsy way tell how I did it.
 
Last edited:
Today I spent the day cleaning to get some space so I can work on this beast. I have opened the box to look at all the bits but no assembly. Finally did my mock up build all bits accounted for. So neck fits tight, not super tight but good (like i know). I'm still feeling a bit reluctant to drill anything yet! Is it a simple case of trust the pocket drill & bolt the neck on?? What size drill bit for the pilot hole? The body has holes so what's my straight edge blah blah blah. can ya tell i have no idea.
 
what & where do these bits go???

That is a bar style string retainer, it goes on the headstock in between the nut and the tuners. I'm more used to seeing them on guitars with Floyd Rose bridges and locking tuners, but I imagine on a 12-string guitar it will help with tuning stability
512.jpg

There's some beautiful grain on that body; looking forward to seeing how this turns out!
 
String retainers are often on FR and other floating bridges to stop the strings popping off the nut on wild bends... on that 12 string, though, all I see is another friction point where you least want one?!?
 
1) This is where I'm at after bit more fluffing around. Not confident with the pick guard. Can it be reshaped? what Tools?
I think if i can shave a bit of at the the neck & where it meets the control plate I may use it (I still like what cork sniffer has done)
47002282252_0db2365d1b_z.jpg


2) the stings look ok down the neck I'm leaning towards moving the bridge 2mm towards the low E string??
46145138445_24368b29a6_z.jpg

40093898733_cf0c016eef_z.jpg


3) If i do move it a few mm will it impact on the stringing up via the through holes on the body?? its only 2mm?? is it even worth doing it for that amount?
46334918744_4792baa217_z.jpg


4) And then there is these holes that I didn't put there? I noticed these as i was lining up the bridge which seems ok? the PU is up against the cavity wall. One of the reasons I'm leaning towards moving the bridge 2mm??
46145157745_f477072cf8_z.jpg


don't know?? still not feeling confident.
 
Last edited:
Yhep the pickguard always needs a bit of tweaking on the Tele. I just use my sanding tool on the dremel.
 
Ok, fine grit? Are you wedging it between anything or clamping it to a bench? did it vibrate? I'm freak'n out.

If you're worried, do both. clamp it down to your bench between two pieces of wood or similar. And only feed out as little of the area as possible that you are working on.
 
Ahhh, I usually just hold it. the dremel at high speed doesn't vibrate very much. if you want to get a feel practice on a bit of scrap wood or something.

I usually shape the half semi-circle for the control plate first. take a little bit off, then check, take a little bit off, then check

What happens is the whole pickguard can then come downwards on the right side a bit which fixes the issue on the horn side and makes it parallel with your bridge.

Then it will stick out in the neck pocket. at that stage, if I'm happy with the placement, I will drill the holes fit the pickguard and use the dremel to sand the pickguard out of the neck pocket.

Just one way of doing it.
 
Back
Top