Hi All My Dingotone Guitar wax arrived yesterday and is very hard and dry. Is there a preferred method of softening it up or would a bit of heat do the job?
Hi All My Dingotone Guitar wax arrived yesterday and is very hard and dry. Is there a preferred method of softening it up or would a bit of heat do the job?
guitars:- Mini Maton acoustic
Fender CN 240 SCE thinline nylon acoustic
Yamaha G228 Classical
Godin Tele style LR Baggs electric
Freedom Chinese LP
Monterey Chinese Resonator guitar
No Name Chinese 12 string electric
Home build tele style electric
Stewart McDonald ukulele kit
Home build ukulele
Pit Bull ES 1g Just out of box...............
A few weeks ago I put mine through the microwave at 30 seconds to begin with and then additional 10-20 second intervals until things softened up. Just need to be careful as the centre will soften and melt first and if you go too long it will end up as hot as molten lava.
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
I tried the microwave and didn't like the control I had over it.
I just dig a bit out and ply it in my fingers for a minute or so while my body heat warms it up. stick a bit on a rag with an eraser in it and apply to each fret. I keep kneading it in my fingers so it stays soft and put little bits on the rag as i go. once done, I get a coarser rage and wipe off any excess, then polish.
Build #1 - ST-1 - Completed
Build #2 - LP-1SS - Completed
Build #3 - TLA-1R - Completed
Build #4 - SGD-612 - Completed
Build #5 - ES-1G - Completed
Build #6 - STA-1HT | Completed
Build #7 - ST1JR - Completed
Current Build #8 - JBA-4
Build #9 - Semi-scratch build Tele x 2 - Completed
Current Build #10 - PRS-1H
Current Build #11 - AGJR-1 - Completed
Current Build #12 - ATL-1SB
Current Build #13 - GST-1
Current Build #14 - FBM-1
Fair comments Andy. Just found mine had solidified as hard as petrified wood and needed a bit of external heat source to help things along a bit so that working with fingers was manageable.
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
I sat mine in a bowl of hot water, then applied at low speed with a polishing mop on the dremel
Build 19 PSH-1 Kustom
Build 18 HB-4S Kustom
Build 17 WL-1 Kustom
Build 16 TL-1TB Kustom
Build 15 PBG-2-
Build 14 FTD-1
Build 13 RD-1 Kustom
Build 12 DM-1S
Build 11 MKA-2 -
Build 10 Basic strat
Build 9 JM Kustom
Build 8 FV-1G
Build 7 ES-2V
Build 6- Community prototype
Build 5 LP-1LQ
Build 4 ES-5V
Build 3 JR-1
Build 2 GD-1
Build 1 TLA-1
I've not used Dingotone wax,
I've found that if I leave my Mr. Zog's Sex Wax out in the sun it gets soft and runny.
![]()
Col.
I admit that I am an agent of Satan, however, my duties are largely ceremonial.
\m/
Thanks a lot for your advice fellas. I was thinking of hot water or the heat gun. We'll see how I go
guitars:- Mini Maton acoustic
Fender CN 240 SCE thinline nylon acoustic
Yamaha G228 Classical
Godin Tele style LR Baggs electric
Freedom Chinese LP
Monterey Chinese Resonator guitar
No Name Chinese 12 string electric
Home build tele style electric
Stewart McDonald ukulele kit
Home build ukulele
Pit Bull ES 1g Just out of box...............