Hello, I have a question, someone can tell me if the pills that bring matter where in site put?
one is 12k and one 13k, but not if heeding the impdeancia or frame they bring.
Thank you
Hello, I have a question, someone can tell me if the pills that bring matter where in site put?
one is 12k and one 13k, but not if heeding the impdeancia or frame they bring.
Thank you
ManCamba...where are you from? I am not able to understand the question. sorry mate.
Build #1 - ST-1 - Completed
Build #2 - LP-1SS - Completed
Build #3 - TLA-1R - Completed
Build #4 - SGD-612 - Completed
Build #5 - ES-1G - Completed
Build #6 - STA-1HT | Completed
Build #7 - ST1JR - Completed
Current Build #8 - JBA-4
Build #9 - Semi-scratch build Tele x 2 - Completed
Current Build #10 - PRS-1H
Current Build #11 - AGJR-1 - Completed
Current Build #12 - ATL-1SB
Current Build #13 - GST-1
Current Build #14 - FBM-1
ayuda GR1-SF
Hola,tengo una duda,alguien me puede decir si las pastillas que trae da igual en que sitio se pongan ?
una es de 12k y otra de 13k ,pero no se si hacer caso a la impedancia o al marco que traen para qiue la altura sea correcta.
Gracias
Ok, I think I know what is going on here. In Spanish, the word 'pastillas' is used for pickups, but translates into English as 'pills'.
ManCamba, the higher rated pickup (13k) usually will go in the bridge position and the lower one (12k) will go towards the neck.
I hope that's right. lol
Last edited by pablopepper; 16-08-2016 at 08:47 AM.
'As long as there's, you know, sex and drugs, I can do without the rock and roll.'
Wow Pabs I really had no idea what was going on. If its a Pitbull Kit, doesn't then length of the wires from the pups give it away? ie the pickup with the longer wire will go in the neck position.
Build #1 - ST-1 - Completed
Build #2 - LP-1SS - Completed
Build #3 - TLA-1R - Completed
Build #4 - SGD-612 - Completed
Build #5 - ES-1G - Completed
Build #6 - STA-1HT | Completed
Build #7 - ST1JR - Completed
Current Build #8 - JBA-4
Build #9 - Semi-scratch build Tele x 2 - Completed
Current Build #10 - PRS-1H
Current Build #11 - AGJR-1 - Completed
Current Build #12 - ATL-1SB
Current Build #13 - GST-1
Current Build #14 - FBM-1
That too. I think the leads are usually red from bridge and yellow from the neck pickup as well.
'As long as there's, you know, sex and drugs, I can do without the rock and roll.'
Hi Mancamba, not much point writing your questions in Spannish not many will understand.
As others have said usually the neck pup will have a longer wire and a slightly lower resistance reading.
Ignore the wire colours as they vary alot between the kits.
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
the wire are the same length,
wrote in Spanish if my translator did not do it well.
thanks to all,
Posting Permissions
Reply With Quote