Hey guys need help urgently!
My garage ceiling sprung a bad leak right over the lacquered body of my ESP1.
Parts of the body have bowed.
Fortunately the neck was spared.
I need suggestions guys please!!!!!
Hey guys need help urgently!
My garage ceiling sprung a bad leak right over the lacquered body of my ESP1.
Parts of the body have bowed.
Fortunately the neck was spared.
I need suggestions guys please!!!!!
Hi Loose12, can you please post some photos how badly the body has bowed ? Do you mean parts of the timber grain has lifted ?
Doesn't sound good, all you can do at this stage is hang it somewhere safe to dry.
At best you will probably have to sand it back to bare wood, depends how bad the water damage is
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Dependiing on how badly and where it has actually bowed it may be possible to clamp or compress it straighter while it dries. But, as Wokka says, we need some pictures before we can offer any real advice.
Scott.
post some pics as the others have said, we might be able to save it
Stan's LP Build for my Sister: http://www.buildyourownguitar.com.au...ead.php?t=3146
Benson Pickup Strat mod: http://www.buildyourownguitar.com.au...ead.php?t=5229
Epiphone LP headstock fix: http://www.buildyourownguitar.com.au...ead.php?t=3410
Martin Backpacker Repair: http://www.buildyourownguitar.com.au...?t=5038&page=3
'57 Harmony Jazz guitar project: http://www.buildyourownguitar.com.au...ead.php?t=2972
Hi wokkaboy,
It has lifted the grain in parts near the pick up and knob holes.
And a long lift on the back.
Can't really see it in photos, but you can feel it.
Ahhhh, this sounds like a case of my fave... Sanding.....
You should be able to sand out the lifted areas and refinish
There is always a workaround for glitches, mistakes and other Guitar building gremlins.....
Loose, if the lifted parts can't be seen in photos can't be too bad then.
I'd do as Weirdy suggested get a flat piece of wood and clamp the surface, use a rag for the other side to protect the surface.
You got nothing to lose trying this.
Otherwise its a sand back to bare wood !
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
otherwise send it to DB he loves sanding that much hahahaOriginally Posted by dingobass
(just joking !)
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
If the timber is still damp, grab an old tea towel and sneak the household iron out (just don't get caught, wives and mothers have a thing about us guys using the iron for non clothing type jobs)
Set it on a cool setting and lay the tea towel over the areas affected and gently force dry it, the grain should shrink back to somewhere close to its correct place.
You will still have to sand it all back though........
There is always a workaround for glitches, mistakes and other Guitar building gremlins.....
Haha thanks for your help guys.
I'll try the clamping first, keep you posted
Posting Permissions
Reply With Quote
