Results 1 to 8 of 8

Thread: Bridge routing and/or neck shims.

  1. #1
    Mentor ozzbike's Avatar
    Join Date
    Aug 2014
    Location
    Sunshine Coast, Queensland
    Posts
    1,109

    Bridge routing and/or neck shims.

    Guys,

    I have made a couple of bass guitars now and note that compared to manufactured ones they seem a little high with the action.

    I had read a couple of build diaries here with references to "Recessing the Bridge."

    My queries are:-

    1. What tools are being used to make the recess? e.g. Dremel, ozito rotary tool.....and with what attachments. Please excuse the Big Green shed reference....but easiest place for me to chase these things down. I was thinking of these two things....cheaper.

    http://www.bunnings.com.au/ozito-170...l-kit_p6290175

    http://www.bunnings.com.au/craftrigh...-case_p6312374

    as opposed to this....dearer.....

    http://www.bunnings.com.au/dremel-13...l-kit_p6280040

    http://www.bunnings.com.au/dremel-pl...hment_p6373700

    2. How do I correctly measure any such recess to ensure I dig the correct hole?

    3. Do I need to do both...shim and recess or is one better than the other.

    Thank You for your ideas.

    Greg

  2. #2
    Overlord of Music gavinturner's Avatar
    Join Date
    May 2013
    Location
    HOLGATE NSW
    Posts
    3,057
    Hey greg,

    Personally, if you have the guitar finished and assembled already, then a shim is the most painless way to go. All you need to do is loosen the strings, unbolt the neck and make a shim to go in the bottom half of the neck pocket. You can do this without any risk to your instrument - if you dont like it, then just take it out again! I usually make my shim out of plastic milk bottle. Maybe not the purest of luthier materials, but it's easy to work with, it won't compress easily, and I've had great results on a number of builds.

    I remove the neck from the pocket, leaving the neck bolts in place (sticking just out of the holes). Cut the plastic to the shape of the bottom end of the pocket and then press it down onto the tips of the bolts sticking through the holes so that they puncture it. Use some scissors to trim off the plastic that has been pushed up and the shim should be able to go over the bolts and sit flat in the neck pocket. Re-attach the neck, check your action and (hopefully) adjust the bridge to bring the strings up off the lowest frets.

    If the neck angle isn't back far enough, you might need a second layer, but I never have yet.

    Hope this helps.

    cheers,
    Gav.
    Last edited by gavinturner; 10-05-2015 at 08:14 PM.
    --
    Build #01: BC-1
    Build #02: ST-1
    Build #03: JR-1DC
    Build #04: ES-2V
    Build #05: ESB-4 (GOTM July 2014)
    Build #06: RC-1
    Build #07: MK-2
    Build #08: TLA-1
    Build #09: JR-1DC
    Build #0A: LPA-1
    Build #0B: STA-1 (GOTM April 2015)
    Build #0C: MKA-2
    Build #0D: LP-1M
    Build #0E: JB-1
    Build #0F: FS-1

    Find me:
    https://www.facebook.com/firescreek.guitars/
    http://www.guitarkitbuilder.blogspot.com.au/

  3. #3
    Overlord of Music
    Join Date
    Aug 2012
    Location
    Brisvegas
    Posts
    3,356
    I agree with Gav. A shim is quick and easy and can make a dramatic difference. Plus, it's easy to adjust or remove completely. I use scraps of wood veneer.
    'As long as there's, you know, sex and drugs, I can do without the rock and roll.'

  4. #4
    GAStronomist stan's Avatar
    Join Date
    Aug 2013
    Location
    Geelong, Vic
    Posts
    5,290
    that is a sweet tip Gav, noted...

  5. #5
    Moderator dingobass's Avatar
    Join Date
    Sep 2012
    Location
    Perth
    Posts
    4,491
    If you find the milk bottle plastic is a touch too thick, try photocopy paper soaked with thin CA glue.

    There is always a workaround for glitches, mistakes and other Guitar building gremlins.....

  6. #6
    Moderator dingobass's Avatar
    Join Date
    Sep 2012
    Location
    Perth
    Posts
    4,491
    Oh, and with the rotary tool question go for the Dremel.
    Sure, costs a bit more but the difference in quality more than makes up for the cost.
    My Dremel must be pushing 20 years now and it still does a great job.. I use it several times a week.

    The thing is, you are always better off to spend a few dollars more on tools.
    Cheap tools give cheap results.

    There is always a workaround for glitches, mistakes and other Guitar building gremlins.....

  7. #7
    Mentor ozzbike's Avatar
    Join Date
    Aug 2014
    Location
    Sunshine Coast, Queensland
    Posts
    1,109
    Wow thanks guys for the info. DB I think I shall save a few pennies and get a dremel. I think a powered one will suit me better than a rechargeable.

    Photocopy paper seems to be used for lots....wudtone finishing....so that is photo copy paper with a little super glue on it....awesome tip guys.

    Gav, are you serious....the plastic from a milk bottle. Wow. Like the flat side of one of those square 2 litre ones??? That works well for you. Amazing. Thanks for the hint.

    I am trying to resurrect the purple wreck from last year that has been sitting in the corner smugly sneering at me.

  8. #8
    GAStronomist stan's Avatar
    Join Date
    Aug 2013
    Location
    Geelong, Vic
    Posts
    5,290
    Quote Originally Posted by dingobass View Post
    If you find the milk bottle plastic is a touch too thick, try photocopy paper soaked with thin CA glue.
    awesome tip DB!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •