Hey guys
i purchased a ES-1GT it looks amazing already in all its peices.
Im frothing to get it started but i dont know how to go about soldering everything with such little workspace, i think all i have to play with is the f holes on the top! has anyone done these or something like this and can give me a complete novice some helpful advice or tricks!!!. I've watched some videos but i cant seem to find a guitar similar all else seem to have areas that are open.
Any advice and help will be greatly appreciated
Cole
I'm about to tackle wiring my ES-1G L...so I'm feeling your pain.
I've also seen (and I'll have to do some digging in my youtube history and post it back up) where you put all the parts through a shoe box in the exact configuration, prewire it all outside the box, then stuff it all in the F-hole...
If you have a look at the thread i put together showing my method you will see that I used a flat piece of perspex, however, I did that so that folks could see what was happening above and below the surface of what I was doing. Any flat piece of cardboard or wood will do. Just needs to be thin enough to attach the pots. The key reason is to get an idea how long the wires need to be although we do recommend soldering away from the finish of your guitar so this method should be used for all guitars where possible. I believe the beginner should make these wires longer so that you can individually remove a pot or switch from the body if something is buzzing or simply not working. Its not as easy as it looks though because when you start to pull things through the 'f' hole things begin to get tangled! That's when tempers get frayed.....
I do like how it has been taped up to minimise the tangle possibility. Now, do I remove all my wiring from my build and redo it this way....Not a chance! Not with the money I spent on counseling!
I wired up my 1G last year and after ungoing the recommended counselling managed to get some very good use from a lovely bit of kit, however just recently one of my pickups failed....after breaking out in a cold sweat with the possibility of having to rewire the whole thing I placed the axe gently in the corner and eventually contemplating a return to insanity, I bit the bullet a couple of weeks ago and downloaded the wiring diagram, which was quite different to the wiring diagram I had used previously, and after removing the previous wiring through the F once again I tried to rewire using the existing pots and wires which proved to be more frustrating than I could imagine. So I took myself off to purchase four new pots and more wire...I have rewired according the new general wiring diagram for 2 humbucker, 4 pots and a 3 way switch......I still have all the wiring outside of the guitar and it doesn't work on all three switch positions only one (the bridge pickup)....I am now beginning to consider that the switch might be faulty...without buying a new one, is there any way to check the switch and what was the rationale behind changing the wiring configuration of the 1G please.
Pete,
In terms of checking switches - check out DingoBass' post in the below - multimeter - red to in from the pickup, black to output from the switch. See how that works. http://www.pitbullguitars.com/?page_...wtopic&t=230.5
In terms of changes to the wiring diagram, as with everything, there's more than one way to skin a cat. The guys at PBG have tried to standardise all the wiring diagrams to be consistent. Is one way better than another - depends on the person - some like to have their caps between pots - others wire and do it that way. Both work and give a similar outcome - as such neither is wrong. If however there are problems with a wiring diagram - put in a post - I'm happy to update them and correct any defects.
Thanks Very much for your prompt reply Brendan, no I don't believe there is anything wrong with the diagram, rather with (1) the operator or(2) the switch, I have triple checked my wiring but I was intrigued to see both pickup ground wires going to the neck volume pot....!!
Pete - bear in mind - all of your pots will be grounded to each other with the wires marked in purple. Apparently having both pups go to one pot will reduce the chance of forming a loop or something like that... In reality, I don't think it matters if they go to one pot or the other - so long as they are all joined together (and not in a loop ).
Reply With Quote
Gavmeister
).
