Marcel's folley #6 a PRS-1H

[Marcel]

What are you worrying about? I dropped nearly $300 on a pair of SD Black Winter and nearly $200 on a set of Lace Dissonant Agressors. Neither set is likely to get fired up anytime soon.

Fool? Nay sir, you are a sober and reasoned gentleman by comparison. As for me, I blame Igor, he can't help himself when it comes to shiny things.

I know the feeling all too well FW ... On a early Strat build I threw $450 on a set of SD PU's, then there was the tuners, the bridge, the switch & pots & guard, & nut on top of getting the body and neck separately and putting a finish on the bugger... mind you I think it was worth it.... and despite the wonderful Bling aspect it gets harder to rationalise these 'improvement' things as funds grow tighter...

[FrankenWashie]

I know the feeling all too well FW ... On a early Strat build I threw $450 on a set of SD PU's, then there was the tuners, the bridge, the switch & pots & guard, & nut on top of getting the body and neck separately and putting a finish on the bugger... mind you I think it was worth it.... and despite the wonderful Bling aspect it gets harder to rationalise these 'improvement' things as funds grow tighter...

Goldurnned shiny guitar thingamys 🤬🤪

[thyoungscientist]

Just Read your comment about the trapeze tailpiece marcel, I think that would make it look pretty nice


(I am also doing the same kit, I am thinking of doing that)

[Marcel]

I did have those thoughts of using a trapeze but have gone with an adjustable Gold wraparound bridge from guitar fetish. Hoping it will be here this week

http://www.guitarfetish.com/Gold-Bad...dge_p_376.html

And over the past few days I've managed to get the blemish fixed. Some careful sanding and some additional coats of clear has rendered the blemish near invisible. I doubt there will be a need for a pick guard now.

[thyoungscientist]

That’s Great! and yeah I might just stick with an adjustable bridge

[Marcel]

Had some time to do a little thinking over this build after a comment was made to me about the F holes.

The comment was the F holes are too big, and as the builder I'd beg to disagree... main reason... all the electronics (as in the pots and switch) has to get fitted via those oversized F holes... there is nil back plate to cover a hole for electronics access.

Which leaves me with what to do if I want phase reversal or coil splitting... Yeah, it is easy enough to wire it up any way I want, but there is that huge F hole gap between the switch and the pots, and nobody like seeing wires all higgaldy-pickaldy across F hole gaps, that's just Yuk! ... so what to do ???

Thinking.... planning... thinking.... planing....thinking....

[Marcel]

Did some of the hardware fit out this afternoon. ... It seems perfection is not my strong point. It all seems only just okay to me...

The new bridge itself is fine, just wish the posts would go deeper in. I cleaned out the holes with a drill but they still sit proud about 2 or 3 mm which is enough to make the action very ho-hummm... I think I need a bigger hammer, but that brings on a whole new set of issues. And getting them out might be a nightmare in itself considering how hard I had to hit them to get them this far.

Will be going the HB/SC switching option on this one. Pull switches on both the vol and tone controls --- vol = neck, tone = bridge.

[Swanny]

Did some of the hardware fit out this afternoon. ... It seems perfection is not my strong point. It all seems only just okay to me...

The new bridge itself is fine, just wish the posts would go deeper in. I cleaned out the holes with a drill but they still sit proud about 2 or 3 mm which is enough to make the action very ho-hummm... I think I need a bigger hammer, but that brings on a whole new set of issues. And getting them out might be a nightmare in itself considering how hard I had to hit them to get them this far.

Will be going the HB/SC switching option on this one. Pull switches on both the vol and tone controls --- vol = neck, tone = bridge.

That's going to look schmick, with the gold, black and red, Marcel! I like it!

I wouldn't be bashing in the bridge posts until it's ready for wiring, if you pull it out and knock it back in it will be a looser fit each time, and you want the bridge earth wire to be nice and firm (unlike my last attempt!)

[Marcel]

That's going to look schmick, with the gold, black and red, Marcel! I like it!

I wouldn't be bashing in the bridge posts until it's ready for wiring, if you pull it out and knock it back in it will be a looser fit each time, and you want the bridge earth wire to be nice and firm (unlike my last attempt!)

I doubt I could pull the bridge posts out even if I wanted to.... They are in pretty damn tight, and they need to go in a few more mm yet. I used a offcut of ply as a cushion when whacking them in this far and now that ply is all dented which is why I stopped. I wish I had my Dad's old fly-press that could give a few tonnes of pressure nice and steady and gently and the job would be so much simpler. I just have to make do with a piece of Pine or Maple and a bigger hammer. The alternative is build a lever-press out of Uni-strutt which is a lot of effort for one task, but may do the job better. Oh-well, this is yet another thing to ponder over...

[Swanny]

I doubt I could pull the bridge posts out even if I wanted to.... They are in pretty damn tight, and they need to go in a few more mm yet. I used a offcut of ply as a cushion when whacking them in this far and now that ply is all dented which is why I stopped. I wish I had my Dad's old fly-press that could give a few tonnes of pressure nice and steady and gently and the job would be so much simpler. I just have to make do with a piece of Pine or Maple and a bigger hammer. The alternative is build a lever-press out of Uni-strutt which is a lot of effort for one task, but may do the job better. Oh-well, this is yet another thing to ponder over...

I used a short socket extension as a drift, one sharp hit at a time. It’s nerve wracking!