Maybe this can work ?
Sharplace Forets HSS Hélicoïdaux Mèche pour Plastique Bois Métal - 1,0 mm à 3,0 mm https://www.amazon.fr/dp/B074QG3B8H/..._E3wrAbDRMGPCF
Maybe this can work ?
Sharplace Forets HSS Hélicoïdaux Mèche pour Plastique Bois Métal - 1,0 mm à 3,0 mm https://www.amazon.fr/dp/B074QG3B8H/..._E3wrAbDRMGPCF
Last edited by Volgar; 14-01-2018 at 08:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Hi Maxence,
the diagram below illustrates the difference. What you had with the bigger set of bits is called a twist drill bit.
The spike helps centre the bit on your drill mark, with a twist bit, the end can wander as the drill begins to rotate before it "bites" into the wood. This can be a big problem when you are drilling by hand held drill.
The set you have shown is a good set, but you must be very careful to punch mark each hole before you begin to drill, and you must be very accurate with the hand held drill.
FrankenLab:
Turning tone wood into expensive sawdust since 2016!
After searching for hours,
I can't find anything on amazon :/
The smallest tip is on the given link! : /
Is there really brad point bit of 1, 1.5, 2mm ? :/
I search on amazon, ebay, aliexpress, and all french big brands of "do-it-yourself" (I don't know if it's the word) stores and nobody sell this ! :/
Last edited by Volgar; 14-01-2018 at 08:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
For the really small sizes, 1 and 1.5mm you'll probably have to use the standard twist drills. From what i have seen the bradpoints start at 2mm, the most common size sets start at 3mm.Originally Posted by Volgar
When you drill the smallest holes, just make sure you use a nail or a sharp punch to mark the spot to give the drill something to locate the tip and prevent it moving sideways on you.
FrankenLab:
Turning tone wood into expensive sawdust since 2016!
Maybe these can work ?
- 1 & 1.5 mm
- 2 mm
- 3 mm
Last edited by Volgar; 14-01-2018 at 08:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Yeah they should work fine, like i said you will just need to be super careful in punch marking the holes and in starting your drill hole.
FrankenLab:
Turning tone wood into expensive sawdust since 2016!
Ok thanks,
Only One drill bit for 1mm is good ?
Last edited by Volgar; 14-01-2018 at 08:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
First part is here !
And ... in bonus my new pedal, who arrived at the same time
Last edited by Volgar; 14-01-2018 at 08:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Mooer Black Secrets are phenomenal RAT clones, especially for the price and for their size!
I am a big fan.
And after an ultimate check, here's the list of buyed items :
- 2 mm drill
- 1 & 1.5 mm drill
- 3 mm drill
- Woodfiller
- Straightedge
- Sandpaper
- Fret file
Last edited by Volgar; 14-01-2018 at 08:25 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Posting Permissions
Reply With Quote