The good Doctor was kind enough to make me a Big Muff circuit board, all new ground to me, this wiring stuff,if I can get a straight run at it I'm feeling confident of not stuffing it up, but I keep getting interruptions.
The good Doctor was kind enough to make me a Big Muff circuit board, all new ground to me, this wiring stuff,if I can get a straight run at it I'm feeling confident of not stuffing it up, but I keep getting interruptions.
Build 19 PSH-1 Kustom
Build 18 HB-4S Kustom
Build 17 WL-1 Kustom
Build 16 TL-1TB Kustom
Build 15 PBG-2-
Build 14 FTD-1
Build 13 RD-1 Kustom
Build 12 DM-1S
Build 11 MKA-2 -
Build 10 Basic strat
Build 9 JM Kustom
Build 8 FV-1G
Build 7 ES-2V
Build 6- Community prototype
Build 5 LP-1LQ
Build 4 ES-5V
Build 3 JR-1
Build 2 GD-1
Build 1 TLA-1
good stuff Dedman lets hope you can get it working like Doc's pedal. You are all setup with the 3rd arm setup !
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
I made one small change from Doc's diagram, I'm putting in a 9v socket rather than battery holder. A small section of SE QLD will probably vaporise when I switch it on :P
Build 19 PSH-1 Kustom
Build 18 HB-4S Kustom
Build 17 WL-1 Kustom
Build 16 TL-1TB Kustom
Build 15 PBG-2-
Build 14 FTD-1
Build 13 RD-1 Kustom
Build 12 DM-1S
Build 11 MKA-2 -
Build 10 Basic strat
Build 9 JM Kustom
Build 8 FV-1G
Build 7 ES-2V
Build 6- Community prototype
Build 5 LP-1LQ
Build 4 ES-5V
Build 3 JR-1
Build 2 GD-1
Build 1 TLA-1
haha I doubt that will happen Dedman, have trust in your abilities !
looks like Wednesday arvo brought to you by the Dedman and Woks show !
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
gonna need a decal for the top of the box I reckon
Build 19 PSH-1 Kustom
Build 18 HB-4S Kustom
Build 17 WL-1 Kustom
Build 16 TL-1TB Kustom
Build 15 PBG-2-
Build 14 FTD-1
Build 13 RD-1 Kustom
Build 12 DM-1S
Build 11 MKA-2 -
Build 10 Basic strat
Build 9 JM Kustom
Build 8 FV-1G
Build 7 ES-2V
Build 6- Community prototype
Build 5 LP-1LQ
Build 4 ES-5V
Build 3 JR-1
Build 2 GD-1
Build 1 TLA-1
Looking good so far Dedman, the pedal should work fine with the 9V DC socket, you might get a bit of hum from the power supply coming through but it should work the same as for a 9V battery, I may even mod my Big Muff to allow it to be powered from a 9V DC socket at some stage this year, looking forward to hearing the finished pedal.
That Dr Fuzz logo looks cool, it'll definitely look great on the pedal.
Originally Posted by wokkaboy
You forgot to mention the good Doc too...hahahaha....
cool logo for the top Dedman.
Sorry Doc I didn't mention you as I trust your circuit will work fine and not cause any natural disasters haha
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Haha...that's okay mate, if any natural disasters do occur I shall assume full responsibility for them, you can then point the finger directly at me and exclaim..."He did it!!!".....hahahaha....
nah Doc with your electronics background I have total faith in your work. Plus can the circuit board be pre-tested did you do that before you posted it ?
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Posting Permissions
Reply With Quote