Nice!
cheers,
Gav.
Nice!
cheers,
Gav.
--
Build #01: BC-1
Build #02: ST-1
Build #03: JR-1DC
Build #04: ES-2V
Build #05: ESB-4 (GOTM July 2014)
Build #06: RC-1
Build #07: MK-2
Build #08: TLA-1
Build #09: JR-1DC
Build #0A: LPA-1
Build #0B: STA-1 (GOTM April 2015)
Build #0C: MKA-2
Build #0D: LP-1M
Build #0E: JB-1
Build #0F: FS-1
Find me:
https://www.facebook.com/firescreek.guitars/
http://www.guitarkitbuilder.blogspot.com.au/
somewhat of an update... I've been lazy
Sent from my SAMSUNG-SM-G900A using Tapatalk
long time no see Jbird...those acoustics been keeping you busy?
Build #1 - ST-1 - Completed
Build #2 - LP-1SS - Completed
Build #3 - TLA-1R - Completed
Build #4 - SGD-612 - Completed
Build #5 - ES-1G - Completed
Build #6 - STA-1HT | Completed
Build #7 - ST1JR - Completed
Current Build #8 - JBA-4
Build #9 - Semi-scratch build Tele x 2 - Completed
Current Build #10 - PRS-1H
Current Build #11 - AGJR-1 - Completed
Current Build #12 - ATL-1SB
Current Build #13 - GST-1
Current Build #14 - FBM-1
Always!!!! Had a lot going on personally as well
Sent from my SAMSUNG-SM-G900A using Tapatalk
I am not very good with wiring so I'm doing what I can to make this one nice
Sent from my SAMSUNG-SM-G900A using Tapatalk
getting there JBird, be worth putting copper shielding on the bottom of the pickguard, or at least run an earth wire between your tone and volume pots - solder to the back of the pot casings.
You also have to earth the volume lug to the back of the casing, the lug closest to the jack.
You probably haven't got to this yet !
Last edited by wokkaboy; 14-03-2016 at 10:09 AM.
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
I plan on grounding it all just haven't go all the way through it yet
Sent from my SAMSUNG-SM-G900A using Tapatalk
no worries JBird thought that might be the case
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
So wiring sucks!!!! I can't figure out why I get no sound except for a loud buzz when I touch the screws holding the pups to the body or the 3 way switch... its frustrating the hell outta me!
Sent from my SAMSUNG-SM-G900A using Tapatalk
Originally Posted by Jbird
If you have a multimeter, try using it to check if your pickups are all good, you might also need to connect the bridge to a suitable ground point on the back of the volume control pot, does the hum go away when you turn the volume control down?
Posting Permissions
Reply With Quote