Newbie Wiring needing help! No sound when attaching ground wire to jack [ATL-1SB]

[calum-gathergood]

Hey team!

I'm working on my first build and have been following all the guides/videos/diagrams I can find.

Now with everything almost done I feel as if I'm stumbling on the final hurdle with wiring the pickups.

I'm following the TL-1 diagram provided on the Pitbull website - https://www.pitbullguitars.com/wp-co...f/PBG-TL-1.pdf

I've just lightly soldered the connections for the purposes of testing, I plan to tidy things up once I can verify everything is working.

The steps I've taken (bearing in mind that this kit comes with a partially pre-wired set of pickups):

• Connected Neck and Bridge live wires to the 3 way switch
• Connected Neck and Bridge ground wires to the volume pot
• Connected live and earth wires to the input jack.

Before attaching the earth wire I can hear a buzz from my amp as expected, when I attach ground there is silence. However when tapping my pickups with a screwdriver (as shown in the Pitbull YT video) I get no sound. I've tried changing the switch to all 3 configurations, triple checking that the volume pot is turned up etc all to no luck.

I've attached photos to hopefully help, I'm suspicious that the pre-soldered connections on the volume pot are overlapping.

Images HERE

I'd appreciated any help or advice, I've probably made a rookie error but can't find any other ideas through research.

Cheers
Calum

[JimC]

Your connections to the output jack don't look right to me. Conventionally there would be a single shielded cable with the core to the tip and the shield to the rim. I can't see what the shield is doing at the jack end. I suspect your second blue wire is an earth that should go to the bridge. I'm also concerned about loose strands on your pickup wires. I suggest you neaten those up and deal with the loose strands, which have a remarkable habit of finding a way to get in contact with things they shouldn't.

[calum-gathergood]

Thanks for the response JimC!

I can confirm that there are two separate wires both coming from the volume pot. One seems to have double shielding compared to the other but it does not split into two like I've seen in other setups.

Noted on the looses strands, my intention here was to test out my connections before tidying everything up.

[McCreed]

Hi Calum.

At the risk of sounding critical, the way the photo is taken is difficult to see how the wires are connected to the pots and what the quality or condition of those connections may be.

Also because you're using shielded wire on connections between the pots & switch, it's possible you've over-heated the braided wire and melted the insulator to the centre wire causing a short. I have done this when I was learning .

I would suggest de-soldering everything, cleaning up all your connection points (lugs, back of pots) then methodically soldering it all back using single core wire (should have been supplied in the kit) using the diagram I've attached below (the PBG diagram is incomplete for some reason).
By methodically, I mean make your connections in order of the signal path: pickup > to switch > to pots > to output jack. This will help to understand how things should flow so to speak.

Another tip I'll offer is NOT bending the solder lugs on the switch to jump them as you've done. Jump them with wire. The lugs on those import switches are connected via a PCB and I don't know how robust they are. Bending the lugs sideways like that could possibly bugger up the traces in the PCB leading to connection problems. (that is purely speculation on my part, but I personally wouldn't do it that way). And at least one of the lugs on the switch (outer left in photo) looks like it is burnt at the PCB. Switch could be damaged. (????)

Hope this helps.

[calum-gathergood]

Hey McCreed, thanks so much for your detailed response here!

Apologies on the photo quality, happy to take better angled ones if it helps?

Also because you're using shielded wire on connections between the pots & switch, it's possible you've over-heated the braided wire and melted the insulator to the centre wire causing a short. I have done this when I was learning .

This quite possibly could have happened, I'll check the wires.

Thanks for the full diagram, is super handy to have the full picture. I didn't get a single core wire in my kit but I can pick up some wire at Bunnings.

Regarding the lugs on the switch, it actually came shipped like that and I assumed it was purely to make solder easier? I can look into getting a replacement switch if that might be the problem?

I appreciate the time and effort you put into your reply, this really helps me out! Thanks

[Simon Barden]

Also because you're using shielded wire on connections between the pots & switch, it's possible you've over-heated the braided wire and melted the insulator to the centre wire causing a short.

That wiring is the factory supplied wiring, so I'd leave that as it was. The only connections that need to be made with the kit are the two pickup wires to the switch and back of the volume pot, so just concentrate on those for the moment and assume the factory wiring bit is correct. As McCreed says, it would be a lot easier to follow had the factory used single core wire for the pot wiring, but it should work fine once you get the pickup wiring sorted.

[JimC]

What you should have, I think, is one wire that has both a central core and an outer braid.

At the pot end the core will connect to the middle terminal of the pot, and the braid to either one of the other terminals or the body of the pot, it doesn't much matter which. At the jack end the central core should connect to the tip connector, and the braid to the other terminal.

I can't see clearly, but I suspect the second blue wire is a plain wire with just a core, no braid, and is soldered to the body of the pot. This is almost certainly the earth wire for the bridge, and instead of running to the output jack it should connect to the bridge. Usually there's a hole to underneath the bridge, and the end is splayed out slightly without solder and crushed between the bridge and the body to make a good enough contact.

The little puzzle we have is that whilst bridge earth to jack earth isn't right, it probably ought to work, albeit noisy, so there is something else going on that I haven't spotted from the photos. My first guess is something to do with the screen/shield/braid for the jack connection, which I can't see, and the second would be something bridged at the switch. A close up of the jack might be helpful.

McCreed, my understanding is that the PB diagram only contains the connections that the customer is required to make, the rest is all pre connected, and I assume the shielded cable was supplied with the kit. Although I agree with you that we may come to having to take it all apart and starting again, I'm loathe to suggest it until we have eliminated issues with the jack connections. I do share your concern about the switch, and whether it may have been overheated, but I strongly suggest getting the jack connection right first, and only then working back to the switch.

[calum-gathergood]

Ok I think I have a wire that has a central core attached to the pot, funnily enough it appears that the other end is partially stripped and tinned so I'll just need to cut it shorter.

Ok great, I was wondering about the bridge wire, that's good to know I'm using it incorrectly.

After McCreed's comment I'm suspicious about whether or not the switch is faulty.

Thanks for the advice, I'll try out your suggestions. Cheers!

[JimC]

Ok I think I have a wire that has a central core attached to the pot, funnily enough it appears that the other end is partially stripped and tinned so I'll just need to cut it shorter.

NO!
Don't do that.
The blue earth wire needs to be taken off the output jack completely, and that stripped tinned shield wire soldered in its place.


BTW, as a general tip, I don't suggest lightly connecting the wires for testing. Connect them up as you mean to leave them.
Several reasons, but among them are
Once you have it working you really don't want to take it apart again and maybe get it wrong the second time.
It tends to be a lot more fiddly to reconnect wires that have already been soldered to tags that have already been soldered.
Modern plastic based components are prone to melt if overheated, so the fewer times you solder to them the better.
Connecting up less neatly for testing means its more likely something will go wrong.

[Simon Barden]

NO!
Don't do that.
The blue earth wire needs to be taken off the output jack completely, and that stripped tinned shield wire soldered in its place.

NO! Please don't do that.

Jim is easily confused. The factory wiring looks OK. Pickup wire connections only.