Good advice Chuck.Originally Posted by Chuck
On my latest Tele I cut the decal slightly bigger than the headstock and trimmed it back after drying so that is was covering the whole headstock face therefore edge line of the transfer was not visible, as is the case on the other 4 builds where I trimmed to the edge of the logo.
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
It also pays to use a decal solvent - Microsol was my chosen one - when applying the decal to move it around without tearing it; ask me how I know!!
Be aware, too, that sometimes when you're clearing over the dry decal, crazing can occur in the decal... I'm unsure why it happened to my project but it most surely did!
"If it's Blues music in a bar and it helps people swallow their drink of choice, or it's a dance song and people get up off their chairs and shuffle their feet, or it's a Jazz tune and the Chardonnay tastes so much better... then it's all good."
- Marcel
A smear of soapy water on the surface before applying the decal has a similar effect, allowing you to move it around until the water dries.
Dishwashing liquid works well.
Yes, it does but the Microsol also softens the carrier film and allows the decal to sit lower on the piece.
"If it's Blues music in a bar and it helps people swallow their drink of choice, or it's a dance song and people get up off their chairs and shuffle their feet, or it's a Jazz tune and the Chardonnay tastes so much better... then it's all good."
- Marcel
good tips Corsair and Hoby. The clear paper can tear or stretch pretty easy when you are getting the right placement for them. I've applied that many that I don't even have to think what I'm doing.
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Thanks for the explanation and tips guys. Shouldn't be that hard to do so I'm going for it.
Nr 1: Red Widow LP-1MQ (Finished) ->Diary<-
Right. Forecast no rain and good weather.
I'm sprayin it !
Sent from outta space using MartianTalk
Tele Deluxe: http://www.buildyourownguitar.com.au...ht=tele+deluxe
Johnny Ramone:https://www.buildyourownguitar.com.a...=johnny+ramone
ES2V:https://www.buildyourownguitar.com.a...?t=7455&page=9
DMS-1 Mustang: https://www.buildyourownguitar.com.a...=10548&page=12
AG-1 Perhaps i am Tony Iommi: https://www.buildyourownguitar.com.a...t=11537&page=7
Good to know..... I defer to your wisdom.....
Well. I've been offline for a bit.
Here are a few shots of the decal I've put on the deluxe
Sent from outta space using MartianTalk
Tele Deluxe: http://www.buildyourownguitar.com.au...ht=tele+deluxe
Johnny Ramone:https://www.buildyourownguitar.com.a...=johnny+ramone
ES2V:https://www.buildyourownguitar.com.a...?t=7455&page=9
DMS-1 Mustang: https://www.buildyourownguitar.com.a...=10548&page=12
AG-1 Perhaps i am Tony Iommi: https://www.buildyourownguitar.com.a...t=11537&page=7
Sent from outta space using MartianTalk
Tele Deluxe: http://www.buildyourownguitar.com.au...ht=tele+deluxe
Johnny Ramone:https://www.buildyourownguitar.com.a...=johnny+ramone
ES2V:https://www.buildyourownguitar.com.a...?t=7455&page=9
DMS-1 Mustang: https://www.buildyourownguitar.com.a...=10548&page=12
AG-1 Perhaps i am Tony Iommi: https://www.buildyourownguitar.com.a...t=11537&page=7
Reply With Quote
