Page 2 of 2 FirstFirst 1 2
Results 11 to 18 of 18

Thread: OK. Help. Stain bleed.

  1. #11
    Thanks all. I came across this little do-hicky this morning at that big hardware place that I'm not a huge fan of. You can adjust the length of the blade. I'll try to attach photos of it. I'm afraid the bleeding has gone too deep in the cracks but I'll give metho a try on them maybe.

    Thanks again,

    Bradboy
    Click image for larger version. 

Name:	Scraper.jpg 
Views:	18 
Size:	52.2 KB 
ID:	31509
    Click image for larger version. 

Name:	Scraper Doohicky.jpg 
Views:	15 
Size:	100.3 KB 
ID:	31508

  2. #12
    Oboe Reed Knife. Works great, better than razor etc, easy to control. You can set your thumb as the depth guide - an oboe knife won't cut you, you can wrap your fingers around it, but it scrapes like the dickens. Pricey these days, but worth it.

  3. #13
    I made a scraping tool out of a 20mm dowel and razor blade similar to the one shown in this link: http://www.homemadetools.net/homemade-binding-scraper-2

    I found it much easier to control than a blade on its own. If you do a web search, there a number of DIY ideas based on the same principle.

    I had everything I needed in my shed already, so it didn't even require a trip to the hardware store.

    And FWIW, I would still mask the binding. Yes, you still have to scrape, but it minimises how much you do by at least 90%.
    Making the world a better place; one guitar at a time...

  4. #14
    Click image for larger version. 

Name:	Front Matt.jpg 
Views:	18 
Size:	113.4 KB 
ID:	31576
    Click image for larger version. 

Name:	Front Colour Enhancer.jpg 
Views:	20 
Size:	122.5 KB 
ID:	31577
    Up to here now. Got some blotches from what I expect is glue so decided to do a burst. Mahogany from black. Thing I noticed is that when I put the colour enhancer on and wiped it off it thinned the black, or the black thinned the mahogany, anyway it's a lot lighter in some places. Doesn't look bad. I just didn't know what to do with the finish to prep it for the colour enhancer and now I'm not sure what to do before the final shiny stuff except just wait.

  5. #15
    In future donít bring the stain to the edge where the binding is, bring it just shy and the Ďbleedí should run and stop before it bleeds into binding.
    I havenít done this on a guitar, but I make wooden furniture for a living and do it this way all the time.
    Last edited by Lokie; 06-07-2019 at 04:46 PM. Reason: Spelling

  6. #16
    Yeah, i kinda thought that but after the conversation and the tips about the bleed i was in two minds. The tape didn't work and ididn't know if the stain would spread. My next one will be a solid body.

  7. #17
    So there I was, with exactly the result on the neck that I wanted after just one coat of satin Cabothane.
    Click image for larger version. 

Name:	Neck 1st Coat Satin.jpg 
Views:	11 
Size:	63.5 KB 
ID:	31623
    Click image for larger version. 

Name:	Neck 1st Coat Satin Close Up.jpg 
Views:	11 
Size:	57.6 KB 
ID:	31624
    But, never satisfied and having read about people sanding between coats I gave it the lightest possible sand I could, but on one part it took all the colour. So I reapplied some black stain and then some colour enhancer and well, it didn't work.
    Click image for larger version. 

Name:	Buggered Neck.jpg 
Views:	11 
Size:	57.5 KB 
ID:	31625
    Am I going to have to sand it all the way back and start again? Any tips welcome.
    Bradboy.

  8. #18
    I tried the dish sponge so a recovery of sorts.
    Click image for larger version. 

Name:	Recovery of Sorts Cropped.jpg 
Views:	9 
Size:	230.2 KB 
ID:	31634

Page 2 of 2 FirstFirst 1 2

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •