1) ES-5V
https://www.buildyourownguitar.com.a...highlight=Es5v
2) ES-3 (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=8953
3) GR-1SF (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=9376
4) Non-Pit Bull Travelling Guitar.
https://www.buildyourownguitar.com.a...ad.php?t=10303
5) AES-1 Special (Unwanted Custom)
https://www.buildyourownguitar.com.a...ad.php?t=11118
This is looking so good DM!
I post this hoping that others will avoid this mistake.
The plastic kit nut from which I used as a guide for my headstock veneer is wider than my ALLPARTS bone nut.
I have ordered an acoustic bone bridge to glue to the back of the nut to fill the gap.
1) ES-5V
https://www.buildyourownguitar.com.a...highlight=Es5v
2) ES-3 (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=8953
3) GR-1SF (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=9376
4) Non-Pit Bull Travelling Guitar.
https://www.buildyourownguitar.com.a...ad.php?t=10303
5) AES-1 Special (Unwanted Custom)
https://www.buildyourownguitar.com.a...ad.php?t=11118
I've had that come up a few times on other peoples guitars. Did a similar fix - I cut a thin strip of black plastic and glued it to the nut to take up space to the truss rod cover. Ends up looking pretty neat.
Build 1 - Shoegazer MK1 JMA-1
Build 2 - The Relliecaster TL-1
Build 3 - The Black Cherry SG AG-1
Build 4 - The Sonicaster TL-1ish
Build 5 - The Steampunker Bass YB-4
Build 6 - The Howling Gowing ST-1
"What I lack in talent I make up for with enthusiasm"
Wet sanding. Some of my later layers must of been applied on a surface without enough key, or the product was being to oxides, or something. When I started sanding I found that they didn’t adhere very well and I had to sand them off. Having said that, they didn’t come off easily either. I went down to 800 wet and dry, 1200 and 1500. I think the problem is resolved and my right ring finger is literally bleeding. I’ll stop now and do the 2000 another day.
1) ES-5V
https://www.buildyourownguitar.com.a...highlight=Es5v
2) ES-3 (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=8953
3) GR-1SF (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=9376
4) Non-Pit Bull Travelling Guitar.
https://www.buildyourownguitar.com.a...ad.php?t=10303
5) AES-1 Special (Unwanted Custom)
https://www.buildyourownguitar.com.a...ad.php?t=11118
First (proper) build: http://www.buildyourownguitar.com.au...ead.php?t=8546
Second build: http://www.buildyourownguitar.com.au...ad.php?t=10229
...though bloodstains could add an interesting effect to the finish
Neglected the family for most of the day to get somewhere on this guitar. It didn’t polish up as well as I hoped, even after sanding pads, but it is was what it is. Lots of cleaning up and setting up to do plus nut to come. Couldn’t resist putting some strings on. Expect it might benefit from pre amp or acoustic amp. I will take it into a guitar shop down the track and test these things.
1) ES-5V
https://www.buildyourownguitar.com.a...highlight=Es5v
2) ES-3 (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=8953
3) GR-1SF (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=9376
4) Non-Pit Bull Travelling Guitar.
https://www.buildyourownguitar.com.a...ad.php?t=10303
5) AES-1 Special (Unwanted Custom)
https://www.buildyourownguitar.com.a...ad.php?t=11118
Turns out that the tailpiece is a terrible place to put a pickup...whoever would of guessed? Pinginess and low volume.
I have cut a slot under the bridge extending the gap for the unit to be glued into. Almost finished, hurry up nut!
1) ES-5V
https://www.buildyourownguitar.com.a...highlight=Es5v
2) ES-3 (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=8953
3) GR-1SF (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=9376
4) Non-Pit Bull Travelling Guitar.
https://www.buildyourownguitar.com.a...ad.php?t=10303
5) AES-1 Special (Unwanted Custom)
https://www.buildyourownguitar.com.a...ad.php?t=11118
And to show you what an idiot I am...I measured the length of the screws for the tuner pegs, not taking into account the thickness of the metal side, and drilled right through the side of the headstock.I might just leave it there to remind me what an idiot I am. Not that I need any reminding.
1) ES-5V
https://www.buildyourownguitar.com.a...highlight=Es5v
2) ES-3 (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=8953
3) GR-1SF (Custom)
https://www.buildyourownguitar.com.a...ead.php?t=9376
4) Non-Pit Bull Travelling Guitar.
https://www.buildyourownguitar.com.a...ad.php?t=10303
5) AES-1 Special (Unwanted Custom)
https://www.buildyourownguitar.com.a...ad.php?t=11118