Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: RCA-4 rebuild

  1. #1
    Overlord of Music
    Join Date
    Aug 2012
    Location
    Brisvegas
    Posts
    3,356

    RCA-4 rebuild

    This has been on my to do list for ages. When I first built my rca-4 I rushed the choice of stain to get the right colour and it has bitten me in the bum. The initially vivid bright blue has faded and turned an ugly, patchy brown/green/blue. I'm sure the ambering of the tru oil hasn't helped, but using stamp pad ink was a terrible idea. Also the action has crept to a point where it is virtually unplayable around the higher frets and is just uncomfortable in general. A bit worrying in a set neck guitar. Anyway, I like this guitar too much for it to continue to gather dust so, a strip down and refinish is in order, and along the way I can fix all the little issues that I was never 100% happy with.



    'As long as there's, you know, sex and drugs, I can do without the rock and roll.'

  2. #2
    Overlord of Music
    Join Date
    Aug 2012
    Location
    Brisvegas
    Posts
    3,356
    For reference, here's what it looked like just after completion 2 and a half years ago.



    Removing the pickguard really emphasised just how bad the fading is. This guitar has never been left in direct sunlight for more than a few minutes at a time.



    Sanding of the back revealed one of the causes of the high action.



    The wood behind the neck pocket has bellied with the strain of the neck. There's about a 2mm drop.
    'As long as there's, you know, sex and drugs, I can do without the rock and roll.'

  3. #3
    Overlord of Music
    Join Date
    Aug 2012
    Location
    Brisvegas
    Posts
    3,356
    Easiest solution I can figure is to inset the bridge. It was bottomed out originally and I should have done it before, but I was too eager to finish (there's a lesson there somewhere). The base plate is 4mm thick, so that's how much I'll drop it. Flush with the top should look pretty schmick.



    Marked out, waiting to make a template.

    And I've carved in a belly contour.



    I've wanted to do this since the first time I played it. The sharpish edges cut into my ribs and made it very uncomfortable to play for any length of time.

    Well, it's a start. Lots more sanding to go.
    'As long as there's, you know, sex and drugs, I can do without the rock and roll.'

  4. #4
    Mentor Andyxlh's Avatar
    Join Date
    Nov 2016
    Location
    Sydney
    Posts
    1,206
    I'm with you there Pablo, I have recently posted a very similar post on my RC 4 kit build thread below. Then finish on mine, poly, is ok except the top which was some pockmarking, but the action is crappy and I need to recess the bridge too. I can't see any movement of the neck pocket, but I'll have a really good look tonight.

  5. #5
    GAStronomist wazkelly's Avatar
    Join Date
    Aug 2015
    Location
    Caloundra West, Sunshine Coast Qld
    Posts
    6,631
    Amazing how much TO keeps on ageing after final prepping.

    I have a similar look on what was a flame maple top blue Tele that now looks more green than blue some 2 years later. I put mine down more to the TO ageing as I used ink jet ink as the stain and that was photo grade stuff.

    Agree about the belly cut as Ric shape is large and can dig into the ribs.

    Weird how the neck pocket bellied out?

    Doing blue again?
    # 1 - EX-5 https://goo.gl/fQJMqh
    # 2 - EX-1 https://goo.gl/KSY9W9
    # 3 - Non PBG Tele https://goo.gl/W14G5g
    # 4 - Non PBG J Bass https://goo.gl/FbBaFy
    # 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
    # 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
    # 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8

  6. #6
    Overlord of Music
    Join Date
    Aug 2012
    Location
    Brisvegas
    Posts
    3,356
    Waz, the extent of the yellowing was a bit of a shock to me. The binding really was looking shabby. And, yeah blue is the plan, but maybe with a black sunburst this time. Maybe.

    Template done, ready to inset the bridge.



    After an hour or so of finessing with an exacto blade and chisel (and proudly with all my fingers still intact) had the rout looking good.



    The baseplate drops in with a satisfying plop. Truth be told, it might end up being a tad too tight after the clear goes on. Deal with that when the time comes.



    And with the saddles on. There's about 2 millimetres of clearance, more than enough. That should take care of the action.



    Final body mod complete. On to the refinish.
    'As long as there's, you know, sex and drugs, I can do without the rock and roll.'

  7. #7
    Mentor Andyxlh's Avatar
    Join Date
    Nov 2016
    Location
    Sydney
    Posts
    1,206
    Nice job! That's exactly how I'll recess my bridge now I know it works 😊

  8. #8
    GAStronomist wazkelly's Avatar
    Join Date
    Aug 2015
    Location
    Caloundra West, Sunshine Coast Qld
    Posts
    6,631
    Top job Pabs.

    Will have to keep an eye on all my TO finished builds to monitor similar yellowing. Only one i have done with binding is the blue, now greenish Tele whilst all other builds won't be as affected due their base colours being in the red/yellow/brown tones.

    Sent from my SM-A520F using Tapatalk
    # 1 - EX-5 https://goo.gl/fQJMqh
    # 2 - EX-1 https://goo.gl/KSY9W9
    # 3 - Non PBG Tele https://goo.gl/W14G5g
    # 4 - Non PBG J Bass https://goo.gl/FbBaFy
    # 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
    # 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
    # 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8

  9. #9
    Overlord of Music
    Join Date
    Aug 2012
    Location
    Brisvegas
    Posts
    3,356
    Sanded, grain filled and stained!

    Still a bit wet and patchy in this pic.


    And after a couple of hours scraping the binding (very tedious, but oh so rewarding).


    And after all that, I got it out to check how it dried last night and accidentally sneezed on it creating a fine pattern of droplets over the top. These all leached a little stain, so I might end up having to redo the top. Joy.
    'As long as there's, you know, sex and drugs, I can do without the rock and roll.'

  10. #10
    Overlord of Music Dedman's Avatar
    Join Date
    Mar 2016
    Location
    The "Fabulous" Gold Coast
    Posts
    3,566
    it's looking dammed sexy Pabs
    Build 19 PSH-1 Kustom
    Build 18 HB-4S Kustom
    Build 17 WL-1 Kustom
    Build 16 TL-1TB Kustom
    Build 15 PBG-2-
    Build 14 FTD-1
    Build 13 RD-1 Kustom
    Build 12 DM-1S
    Build 11 MKA-2 -
    Build 10 Basic strat
    Build 9 JM Kustom
    Build 8 FV-1G
    Build 7 ES-2V
    Build 6- Community prototype
    Build 5 LP-1LQ
    Build 4 ES-5V
    Build 3 JR-1
    Build 2 GD-1
    Build 1 TLA-1

Page 1 of 2 1 2 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •