Just Read your comment about the trapeze tailpiece marcel, I think that would make it look pretty nice
(I am also doing the same kit, I am thinking of doing that)
Last edited by thyoungscientist; 09-12-2017 at 05:24 PM.
I did have those thoughts of using a trapeze but have gone with an adjustable Gold wraparound bridge from guitar fetish. Hoping it will be here this week
http://www.guitarfetish.com/Gold-Bad...dge_p_376.html
And over the past few days I've managed to get the blemish fixed. Some careful sanding and some additional coats of clear has rendered the blemish near invisible. I doubt there will be a need for a pick guard now.
Builds-
#18 PBG GSH-1R https://www.buildyourownguitar.com.a...ad.php?t=10236
#17 PBG PBA-4 https://www.buildyourownguitar.com.a...ead.php?t=9984
#16 PBG IB-1Q http://www.buildyourownguitar.com.au...ead.php?t=8754
#15 PBG TLA-12 http://www.buildyourownguitar.com.au...ead.php?t=8444
#14 PBG PRS-1H
#11 Scratch build AC15 clone headhttps://www.buildyourownguitar.com.a...ead.php?t=7686
#09 PBG ES-1TL
#07 partscaster Alder Denim Tele.
That’s Great! and yeah I might just stick with an adjustable bridge
Had some time to do a little thinking over this build after a comment was made to me about the F holes.
The comment was the F holes are too big, and as the builder I'd beg to disagree... main reason... all the electronics (as in the pots and switch) has to get fitted via those oversized F holes... there is nil back plate to cover a hole for electronics access.
Which leaves me with what to do if I want phase reversal or coil splitting... Yeah, it is easy enough to wire it up any way I want, but there is that huge F hole gap between the switch and the pots, and nobody like seeing wires all higgaldy-pickaldy across F hole gaps, that's just Yuk! ... so what to do ???
Thinking.... planning... thinking.... planing....thinking....
Builds-
#18 PBG GSH-1R https://www.buildyourownguitar.com.a...ad.php?t=10236
#17 PBG PBA-4 https://www.buildyourownguitar.com.a...ead.php?t=9984
#16 PBG IB-1Q http://www.buildyourownguitar.com.au...ead.php?t=8754
#15 PBG TLA-12 http://www.buildyourownguitar.com.au...ead.php?t=8444
#14 PBG PRS-1H
#11 Scratch build AC15 clone headhttps://www.buildyourownguitar.com.a...ead.php?t=7686
#09 PBG ES-1TL
#07 partscaster Alder Denim Tele.
Did some of the hardware fit out this afternoon. ... It seems perfection is not my strong point. It all seems only just okay to me...
The new bridge itself is fine, just wish the posts would go deeper in. I cleaned out the holes with a drill but they still sit proud about 2 or 3 mm which is enough to make the action very ho-hummm... I think I need a bigger hammer, but that brings on a whole new set of issues. And getting them out might be a nightmare in itself considering how hard I had to hit them to get them this far.
Will be going the HB/SC switching option on this one. Pull switches on both the vol and tone controls --- vol = neck, tone = bridge.
Builds-
#18 PBG GSH-1R https://www.buildyourownguitar.com.a...ad.php?t=10236
#17 PBG PBA-4 https://www.buildyourownguitar.com.a...ead.php?t=9984
#16 PBG IB-1Q http://www.buildyourownguitar.com.au...ead.php?t=8754
#15 PBG TLA-12 http://www.buildyourownguitar.com.au...ead.php?t=8444
#14 PBG PRS-1H
#11 Scratch build AC15 clone headhttps://www.buildyourownguitar.com.a...ead.php?t=7686
#09 PBG ES-1TL
#07 partscaster Alder Denim Tele.
That's going to look schmick, with the gold, black and red, Marcel! I like it!
I wouldn't be bashing in the bridge posts until it's ready for wiring, if you pull it out and knock it back in it will be a looser fit each time, and you want the bridge earth wire to be nice and firm (unlike my last attempt!)
1st build - Blue ES-12G ->-Build Diary-<-
2nd build - Father/Son collaboration MB-1 ->-Build Diary-<-
3rd build - GR-SF1 ->-Build Diary-<-
4th build - FS-1 ->-Build Diary-<-
I doubt I could pull the bridge posts out even if I wanted to.... They are in pretty damn tight, and they need to go in a few more mm yet. I used a offcut of ply as a cushion when whacking them in this far and now that ply is all dented which is why I stopped. I wish I had my Dad's old fly-press that could give a few tonnes of pressure nice and steady and gently and the job would be so much simpler. I just have to make do with a piece of Pine or Maple and a bigger hammer. The alternative is build a lever-press out of Uni-strutt which is a lot of effort for one task, but may do the job better. Oh-well, this is yet another thing to ponder over...
Builds-
#18 PBG GSH-1R https://www.buildyourownguitar.com.a...ad.php?t=10236
#17 PBG PBA-4 https://www.buildyourownguitar.com.a...ead.php?t=9984
#16 PBG IB-1Q http://www.buildyourownguitar.com.au...ead.php?t=8754
#15 PBG TLA-12 http://www.buildyourownguitar.com.au...ead.php?t=8444
#14 PBG PRS-1H
#11 Scratch build AC15 clone headhttps://www.buildyourownguitar.com.a...ead.php?t=7686
#09 PBG ES-1TL
#07 partscaster Alder Denim Tele.
1st build - Blue ES-12G ->-Build Diary-<-
2nd build - Father/Son collaboration MB-1 ->-Build Diary-<-
3rd build - GR-SF1 ->-Build Diary-<-
4th build - FS-1 ->-Build Diary-<-