Hi Caitken, whereabouts in the world are you? Perhaps you are near another board member who can have a look at it.
Hi Caitken, whereabouts in the world are you? Perhaps you are near another board member who can have a look at it.
Current:
GTH-1
Completed:
AST-1FB
First Act ME276 (resurrected curb-side find)
ES-5V
Scratchie lapsteel
Custom ST-1 12 String
JBA-4
TL-1TB
Scratch Lapsteel
Meinl DIY Cajon
Cigar Box lap steel
Wishing:
Baritone
Open D/Standard Double 6 twin neck
Comparing it to the one I'm doing at the moment (slightly different model) it looks very much like the neck pocket has not been routed quite deep enough. What glue did you use to glue the neck in?
Edit: I'm in Brisbane and would be happy to help if there's anything you're unsure of.
Last edited by pablopepper; 23-08-2017 at 08:21 AM.
'As long as there's, you know, sex and drugs, I can do without the rock and roll.'
Hi Caitken, sorry I forgot to post a photo of my SG-1F, I will do so tonight and post it.
The neck should have a 3 to 4 degree rake angle downward, is the neck flat with the body Caitken or does it angle back a bit ?
Maybe the neck pocket hasn't been tapered.
EDIT found a pic of the neck pocket and heel I had to chop off the black areas to make mine work. Check out the neck pocket looks deeper than yours and mine is tapered correctly
Last edited by wokkaboy; 23-08-2017 at 10:26 AM.
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
It's all down to small adjustment that needed to be made to the neck heel during construction. Things like this are why it's strongly suggested that you start a build diary on the forum, so we can suggest checks to make along with solutions to problems found before it's too late. None of these kits are 100% perfect, we've all had to deal with different imperfections.
Hopefully Pablo can help with your issues.
yeah Caitken, as Simon suggests see if Pablo can have a look over it to work out whether the neck needs to be removed.
My thoughts are the neck pocket is probably flat where it should taper toward the front of the pocket.
Thats why we always recommend a full mock build with both E strings on before you glue the neck in place.
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
So how did this turnout? Well the problem was that the neck slot had two thin veneer shims on either side - the glue holding these filed so although the neck was glued it was only secured on the bottom. I removed the neck (disturbingly easily) and then re-glued (shims were still attached either side of the neck when I removed it)... and problem solved - now have awesome action on this rig!! HAve to say I'm not that impressed by the titebond glue (first time I've used it) - thinking that PVA might work a whole lot better - although would have had the same problem with the veneer coming away. Anyway - happy with the end product - just a bit of a weird problem to have encountered.
well done Caitken, was worth removing the neck and shimming. Glad you got a good result.
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in