Whoops thought I had started a thread on this....
back, side and neck about done...
Whoops thought I had started a thread on this....
back, side and neck about done...
Build #1 Completed LP1S
Build #2 Completed STA-1M
Build #3 LP1F http://www.buildyourownguitar.com.au...ead.php?t=7767[url]
Build #4 PRS-1 http://www.buildyourownguitar.com.au...ead.php?t=7881[url]
Build #5 ST-1M http://www.buildyourownguitar.com.au...ead.php?t=7961[url]
Build #6 SGM-1 http://www.buildyourownguitar.com.au...ead.php?t=7857[url]
Checked the top for glue marks yet?
3 times Simon.... and will do another try before staining, 1st one showed up a tiny bit near the neck pocket, the binding there had come away slightly too so had to re stick that back using gorilla glue. Fingers crossed.....
Build #1 Completed LP1S
Build #2 Completed STA-1M
Build #3 LP1F http://www.buildyourownguitar.com.au...ead.php?t=7767[url]
Build #4 PRS-1 http://www.buildyourownguitar.com.au...ead.php?t=7881[url]
Build #5 ST-1M http://www.buildyourownguitar.com.au...ead.php?t=7961[url]
Build #6 SGM-1 http://www.buildyourownguitar.com.au...ead.php?t=7857[url]
The join line down the middle seems to be a prime contender for showing up light after staining.
tbh there does look a slight delve there to the eye but after wiping it with meths nothing shows
Build #1 Completed LP1S
Build #2 Completed STA-1M
Build #3 LP1F http://www.buildyourownguitar.com.au...ead.php?t=7767[url]
Build #4 PRS-1 http://www.buildyourownguitar.com.au...ead.php?t=7881[url]
Build #5 ST-1M http://www.buildyourownguitar.com.au...ead.php?t=7961[url]
Build #6 SGM-1 http://www.buildyourownguitar.com.au...ead.php?t=7857[url]
Grrrrr, checked it again before staining...think i need new specs!!!
Hopefully when the stain is dried the gum remover stuff I had will work a bit then a top up with the stain
Build #1 Completed LP1S
Build #2 Completed STA-1M
Build #3 LP1F http://www.buildyourownguitar.com.au...ead.php?t=7767[url]
Build #4 PRS-1 http://www.buildyourownguitar.com.au...ead.php?t=7881[url]
Build #5 ST-1M http://www.buildyourownguitar.com.au...ead.php?t=7961[url]
Build #6 SGM-1 http://www.buildyourownguitar.com.au...ead.php?t=7857[url]
I really like the colour scheme on this project. In the end it should be a pretty one.
Completed Projects:
non PBG LP Custom - Hetfield 'Uncle Milty' Iron Cross replica
non PBG Brownstein Stratocaster
Current WIP:
non PBG Stratocaster - Canadian Red Ensign
PBG FV-1G Custom
Don't worry too much about the glue on the straight bit by the neck pocket as that will be covered by the neck. But the marks near the binding on the curved part of the cutaway will need a bit of attention - though they don't look too bad compared to a lot of other stained tops I've seen here. In fact the stain seems to have taken pretty well - it just seems a bit shinier where there's a bit of glue, which will probably be even less noticeable when you put the clear finish on.
There is a few more very small spots around where the knobs go but I'm not worried about them, as you say it seems to have taken a bit of dye, so may do another deep colour coat tomorrow night then see.....
Build #1 Completed LP1S
Build #2 Completed STA-1M
Build #3 LP1F http://www.buildyourownguitar.com.au...ead.php?t=7767[url]
Build #4 PRS-1 http://www.buildyourownguitar.com.au...ead.php?t=7881[url]
Build #5 ST-1M http://www.buildyourownguitar.com.au...ead.php?t=7961[url]
Build #6 SGM-1 http://www.buildyourownguitar.com.au...ead.php?t=7857[url]
My first glue on neck, easier than what I thought, left it in the clamps for 24 hours just to be sure will let it rest now as probably wont finish the wiring till the weekend and string it up
Build #1 Completed LP1S
Build #2 Completed STA-1M
Build #3 LP1F http://www.buildyourownguitar.com.au...ead.php?t=7767[url]
Build #4 PRS-1 http://www.buildyourownguitar.com.au...ead.php?t=7881[url]
Build #5 ST-1M http://www.buildyourownguitar.com.au...ead.php?t=7961[url]
Build #6 SGM-1 http://www.buildyourownguitar.com.au...ead.php?t=7857[url]