Results 1 to 7 of 7

Thread: First kit build .. is this OK?

  1. #1
    Member
    Join Date
    Dec 2020
    Location
    West Pennant Hills, Sydney.
    Posts
    3

    Question First kit build .. is this OK?

    Hi, I'm building a TLA-1S spalted maple kit. In one place there is a fair bit of tear-out from the thicknesser-planer, and it looks like the factory has applied some filler, and maybe some glue. Now I don't want to sand the veneer, but am wary of the glue causing blotchiness in my stain. Do I go ahead and apply a conditioner/filler, lightly sand, and proceed to stain? Or see if I can send it back?Click image for larger version. 

Name:	20201229_150327.jpg 
Views:	18 
Size:	191.3 KB 
ID:	38607Click image for larger version. 

Name:	20201229_150517.jpg 
Views:	20 
Size:	200.4 KB 
ID:	38608Click image for larger version. 

Name:	20201229_150406.jpg 
Views:	17 
Size:	436.3 KB 
ID:	38609
    Last edited by Browny1010; 29-12-2020 at 12:19 PM.

  2. #2
    GAStronomist FrankenWashie's Avatar
    Join Date
    Jan 2016
    Location
    Glebe, NSW
    Posts
    5,213
    HI Brownie, depending on the extent of the glue/filler issue, you can sometimes work around it using goof off and some careful work with a small wire brush. If the patch is really big and in a noticeable area then less so.

    It helps if you post photos of the problem area, there are a lot of builders who have worked through similar issues that might be able to assist.
    FrankenLab
    “The Hard Way is our speciality”

  3. #3
    Member
    Join Date
    Dec 2020
    Location
    West Pennant Hills, Sydney.
    Posts
    3
    Hey, Franken, thanks for replying. Managed to upload pics ... Would you offer an opinion? I'm a fairly experienced woodworker, but don't want to invest in a bad starting point if the better course was to see if I can swap it out. Cheers.

  4. #4
    Mentor McCreed's Avatar
    Join Date
    Oct 2018
    Location
    AUS
    Posts
    1,689
    Glad to see you got the pic posting sorted.

    Whilst some imperfections can be expected with spalted maple, I would be displeased if that were my order.
    I believe what I can see there could be worked out, but for a first-time build, it poses some extra challenges IMO.

    It would be worth sending the pics to Adam and getting his opinion.
    Making the world a better place; one guitar at a time...

  5. #5
    GAStronomist FrankenWashie's Avatar
    Join Date
    Jan 2016
    Location
    Glebe, NSW
    Posts
    5,213
    Quote Originally Posted by McCreed View Post
    Glad to see you got the pic posting sorted.

    Whilst some imperfections can be expected with spalted maple, I would be displeased if that were my order.
    I believe what I can see there could be worked out, but for a first-time build, it poses some extra challenges IMO.

    It would be worth sending the pics to Adam and getting his opinion.
    I agree with McCreed here, looking at the photos I would raise it with Adam.
    The other thing I'd do is wipe down with White Spirits or Gum turpentine and see if you have further glue bleed issues. If it's just a case of the tear, then potentially you could fill it and have minimal issues, if you've also got lots of glue spots then the problems mount. Especially on a first build it's not ideal.
    FrankenLab
    “The Hard Way is our speciality”

  6. #6
    Member
    Join Date
    Dec 2020
    Location
    West Pennant Hills, Sydney.
    Posts
    3
    Hi McCreed, as suggested, I sent the pics and an email to Adam using the service email address, then rang on the Pittbull number a couple of time to leave voicemails ... all with no response. They processed a second order for tools and stuff last week, so someone is on deck. But no reply to my issue ... any ideas?

  7. #7
    Mentor McCreed's Avatar
    Join Date
    Oct 2018
    Location
    AUS
    Posts
    1,689
    The PBG guys are usually pretty prompt with their communication. I have no other email addresses to offer you.
    I would say just be patient and I'm sure someone will be in touch. (easier said than done I know)
    Making the world a better place; one guitar at a time...

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •