Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast
Results 21 to 30 of 45

Thread: Crane fabric top TL-1

  1. 15-06-2019, 08:09 AM #21
    Kac
    Kac is offline
    Member
    Join Date
    May 2019
    Location
    Perth, Western Australia
    Posts
    22
    Quote Originally Posted by McCreed View Post
    Very nice.
    How are you going to finish the edge where the fabric rolls over? Some kind of piping or something?

    Also to backtrack a little, I'll third the flap disc on an angle grinder as well. Just need to go slow as it will remove material very quickly.

    Keep the pics coming too!
    There is how the edge looks like at the moment, there is a 1-2 mm indentation. I was hopping to build up enough clear resin that I can do a flush trim at the end.

    Reply With Quote Reply With Quote
  2. 15-06-2019, 09:44 AM #22
    Wayne.Mumford
    Wayne.Mumford is offline
    Member Wayne.Mumford's Avatar
    Join Date
    Mar 2016
    Location
    CAMPBELLTOWN NSW
    Posts
    236
    That痴 a real cool look, I have couple of friends that have done cloth tops with great results.
    Wayne.
    Build-1 ES-3 June 2016 GOTM.
    Build-2 IB-1S
    Build-3. ES-12G June 2019 GOTM.
    Build-4 Gene Simmons axe bass. 43 year project done.
    Build-5. TL-1S May 2021 GOTM joint winner.
    Reply With Quote Reply With Quote
  3. 17-06-2019, 11:02 PM #23
    Kac
    Kac is offline
    Member
    Join Date
    May 2019
    Location
    Perth, Western Australia
    Posts
    22
    Done the flood coat of clear resin tonight. Looks promising so far.



    Reply With Quote Reply With Quote
  4. Liked by: corsair, Thunderbird
  5. 18-06-2019, 06:00 AM #24
    I値l give it a go
    I値l give it a go is offline
    Member I値l give it a go's Avatar
    Join Date
    Apr 2019
    Location
    Perth, south of the river.
    Posts
    263
    Looks good, can稚 wait to see the final piece.


    Sent from my iPhone using Tapatalk
    Reply With Quote Reply With Quote
  6. 18-06-2019, 01:10 PM #25
    FrankenWashie
    FrankenWashie is offline
    GAStronomist FrankenWashie's Avatar
    Join Date
    Jan 2016
    Location
    Glebe, NSW
    Posts
    5,666
    Man that is special...absolutely stunning work. Well done!
    FrankenLab
    Hand crafting guitars, because Death Rays are expensive.

    Reply With Quote Reply With Quote
  7. 21-06-2019, 10:00 PM #26
    infxualbydesign
    infxualbydesign is offline
    Member
    Join Date
    Sep 2015
    Posts
    19
    Looks very nice, i vove the matial and placement. Is the edge channel deep enough to put binding on? That might be a nice way to hide the material edge.
    Reply With Quote Reply With Quote
  8. 25-06-2019, 11:02 PM #27
    Kac
    Kac is offline
    Member
    Join Date
    May 2019
    Location
    Perth, Western Australia
    Posts
    22
    Quote Originally Posted by infxualbydesign View Post
    Looks very nice, i vove the matial and placement. Is the edge channel deep enough to put binding on? That might be a nice way to hide the material edge.
    No is not deep enough, I wish I had the router bit for binding that I could do this better, will be so much easier to hide the edge with the binding. Spend last few days redoing the edge, but not a lot of luck so far. I am on the edge of giving up and leave it as it is.
    Reply With Quote Reply With Quote
  9. 25-06-2019, 11:03 PM #28
    Kac
    Kac is offline
    Member
    Join Date
    May 2019
    Location
    Perth, Western Australia
    Posts
    22
    Finally I have finish the headstock.




    Reply With Quote Reply With Quote
  10. 26-06-2019, 01:19 AM #29
    Gavin1393
    Gavin1393 is offline
    Moderator Gavin1393's Avatar
    Join Date
    Sep 2012
    Location
    Mindarie, Western Australia
    Posts
    3,151
    Quote Originally Posted by Kac View Post
    No is not deep enough, I wish I had the router bit for binding that I could do this better, will be so much easier to hide the edge with the binding. Spend last few days redoing the edge, but not a lot of luck so far. I am on the edge of giving up and leave it as it is.
    KAc

    I see you are in Perth...

    If you send me a PM with your contact number I'll help you with the routing channel for the binding...
    http://www.buildyourownguitar.com.au/forum/image.php?type=sigpic&userid=1258&dateline=1443806 448Gavmeister
    Reply With Quote Reply With Quote
  11. 26-06-2019, 09:15 AM #30
    Kac
    Kac is offline
    Member
    Join Date
    May 2019
    Location
    Perth, Western Australia
    Posts
    22
    Quote Originally Posted by Gavin1393 View Post
    KAc

    I see you are in Perth...

    If you send me a PM with your contact number I'll help you with the routing channel for the binding...
    Thanks for the offer, but I have no plans to do the binding for this guitar atm. Maybe in the future project.
    Reply With Quote Reply With Quote
Page 3 of 5 FirstFirst 1 2 3 4 5 LastLast
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules