Page 1 of 2 1 2 LastLast
Results 1 to 10 of 16

Thread: Neck pocket question for non-PBG telecaster kit

  1. #1

    Neck pocket question for non-PBG telecaster kit

    Hello,

    I am a newbie to guitar kit building and I have a question about the neck pocket of my new telecaster kit.

    As you can see in the attached photo, there is a slight gap on the bass side bottom of the neck. I have checked the distance from the top of the fretboard to the body on both the treble and bass sides, and it seems that the bass side is about 1-1.5mm taller than the treble side.

    Click image for larger version. 

Name:	neckpocket.jpg 
Views:	93 
Size:	426.7 KB 
ID:	31704

    Is this a problem? If it is, would it be possible for a beginner to fix such an issue like this, or would it be better to return the kit?

    It is not an issue of the neck not having enough space on the bass side, as it does not fit snug and even when moved the gap is still there.

    I would appreciate any information. Thank you.
    Last edited by koolimy; 25-07-2019 at 02:17 AM. Reason: spelling error

  2. #2
    Overlord of Music dave.king1's Avatar
    Join Date
    Aug 2014
    Location
    Sutherland Shire
    Posts
    2,403
    Welcome to the forum, there will be plenty of advice and assistance from the folks on here.

    What I would do in this case if you intend to finish the kit rather than return is work out if the problem is neck or body and the go and have a chat to the local woodworking shop to get the neck heel thicknesses square or the pocket routed square and then shim to requirement.

    If there's a bit of sideways slop build up the sides of the pocket with copper tape ( slug & snail barrier tape from your local hardware store is the same as guitar shielding tape but much cheaper )

  3. #3
    Thanks for the reply! Does that mean that the issue is serious enough that I should either try to return it or fix it w/ a woodworking shop? I saw that slop on the sides is relatively okay, but I could not find a conclusive answer to whether slop on the bottom (like mine) is okay or not.

  4. #4
    Could be the camera lens but that side of the pocket looks slightly higher.
    Measure it and see.
    Also some folk tend to discard the black plastic plate.
    Perhaps you could trial leaving it out and see if the neck gets pulled further into the pocket.

    Otherwise determine whether it's worth getting a replacement.

    cheers, Mark.

  5. #5
    Thanks for the reply! I just did measurements on the body and the neck and the culprit is most definitely the neck. The body is the same height at both the treble and bass sides, while the neck is taller on the bass side by 1 mm. There also seems to be a bit of a curvature going on at the bottom of the neck.

    If the problem is with the neck, would it be fixable by a beginner? I'm beginning to lean toward returning the kit as I'm worried that it might be out of my league to tackle these problems.

  6. #6
    If it's beyond your capabilities then a replacement (or a refund) would be the best bet.
    If you think it within your ability, perhaps a hefty discount (if you could convince the seller) would make it worthwhile.

    cheers, Mark.

  7. #7
    Click image for larger version. 

Name:	neckgap.jpg 
Views:	85 
Size:	224.9 KB 
ID:	31709Click image for larger version. 

Name:	neckgap2.jpg 
Views:	83 
Size:	241.3 KB 
ID:	31710Click image for larger version. 

Name:	neckgap3.jpg 
Views:	81 
Size:	266.0 KB 
ID:	31711

    It seems like the bottom of the neck has some sort of taper on both sides... I'm guessing this is not normal, right?
    Maybe getting a new kit that doesn't have this problem would be the best way to go haha.

  8. #8
    GAStronomist
    Join Date
    Aug 2013
    Location
    Geelong, Vic
    Posts
    5,269
    mark a pencil line all around the neck heal from the lowest point. That way you can see where the neck is thickest and how much it changes. Then simply use a sanding block to get it flat. Use a hard or firm block and go with care and you should be able to square up the heal

  9. #9
    Hello, I have actually proceeded with building using this kit. I found that the heel part of the neck was flush with every point in the neck pocket. There seemed to be a small tooling/sanding error around the area with the gap, which is the reason why it looks like there is a gap in the neck. All the important contact points, however, seemed to be flush, so I decided to proceed with building with this guitar.

    I however, have a different question. I started to dye my guitar using leather aniline dyes. I left it for about 16 hours, and began applying tru oil to the back of the guitar. I found, however, that some of the dye rubbed onto the rag. How long must one wait to apply tru oil after dying a guitar? Here are pictures of the front and back

    Click image for larger version. 

Name:	IMG_20190811_194736612 (2).jpg 
Views:	24 
Size:	202.8 KB 
ID:	31860

    Click image for larger version. 

Name:	IMG_20190812_194625071.jpg 
Views:	31 
Size:	183.3 KB 
ID:	31861

  10. #10
    GAStronomist
    Join Date
    Aug 2013
    Location
    Geelong, Vic
    Posts
    5,269
    Hard to say - if the Tru Oil is a solvent for the dye, then it will happen every time... Tru oil contains mineral spirits, so if the dye is oil based then you have issues...
    Read the label on the dye - and remember it is designed for leather, and check the cure times. But if it is transferring to your rag then Id assume you would want a minimum 24 hours. If there are no time issues, give it a week. If Tru Oil pulls it up after that amount of time then tru oil is possibly not for this project

Page 1 of 2 1 2 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •