Yep agree you've scored a nice neck there doc, grain looks really nice
Sent from my SM-T700 using Tapatalk
Yep agree you've scored a nice neck there doc, grain looks really nice
Sent from my SM-T700 using Tapatalk
Current Projects
#Planning 5 String Bass
well done Doc neck looking sweet and I see you have pre-drilled all the holes. Must be pretty exciting the build so far !
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Originally Posted by wokkaboy
Yeah it's been pretty exciting, I decided to do a complete test-build before I went and did all the finishing on the body and neck.
good one Doc, so I think the build diary will reach 30 pages before a piece of sandpaper touches the body haha
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Nah,lol, cause I've already given the body a sand with some 180 grit, I haven't applied any Ebony TM yet cause of the glue stains near the top horn on the body, although I may just go ahead anyway, the glue stains aren't that prominent.
Seeing as the neck felt like it was dry to the touch, I decided to go ahead and apply the first coat of Dingotone Colourless Final coat to the neck, it doesn't look much different to how it did in the last pic I posted.
Last edited by DrNomis_44; 13-03-2016 at 11:05 AM.
oh ok Doc good work mate, keep up the good work
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Cheers mate, will do, I'm determined to do a good job at finishing the body and neck.
So far I've had no issues with the new Dingotone MkII, hopefully the Coolangatta Gold MkII should also have no issues.
I think I will go ahead and start working on the body finish today, so stay tuned for some more pics .
Last edited by DrNomis_44; 13-03-2016 at 11:53 AM.
Update:
I decided to go ahead and apply the Ebony Timbermate to the Strat body, I managed to dilute the TM to a nice thick creamy consistency, because I couldn't find a Squeegee, or Spatula, I put one of my spare nitrile gloves on and used my fingers to spread the TM over the body of the guitar, all that's left to do now is wait till the TM has dried and then sand it off, hopefully I got enough of it in the grain to make it pop, here's a pic of the body covered in the Ebony Timbermate:
Last edited by DrNomis_44; 13-03-2016 at 01:57 PM.
Hi Doc, Beware of drippage down the sides! I found this with the EXA body, if you are a little too fluid on the tm then it can leave runs, and even if you attend to them right away, you will get a run mark.
I managed to get around this by sanding back and re-coating with a thin TM solution which effectively filled in around the run marks, leaving it even, although when i first saw them, there was bad words, so many bad words.
Cheers, I think I must have gotten lucky with the consistency of the TM since I didn't get any runs or drips that I could notice.
Posting Permissions
Reply With Quote