So as suggested, I gave it a slight damp wipe to enhance the grain.
Looks to me like the cap continues to the edge based on the continuing grain lines - just that there's a rather major change in colour.
Makes me wonder what that will look like with stain on it. Might affect what stain/darkness I use.
- Sam
IB-5 - was finished, considering re-finishing body
IB-6S - done.
JR-1M - dressing frets and electronics build
ST-1 - still wondering how to install a tremelo
Telebass - non-PBG from parts buiild - painting body
It might affect the hue of the stain, but it's symmetrical so it will still be appealing. Spalt is always a bit random like that.
'As long as there's, you know, sex and drugs, I can do without the rock and roll.'
Hey Sam I wouldn't worry about the lighter edges, as its symmetrical it will be a feature. That is typical of a spalt top can have random colours. I think it will look fantastic with just clear coats and stain the back/sides
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
You think just clear coat the front? Does that mean just top coat, or a "clear" stain? I got some wudtone in the clearance (Amber, Burning Sun and Goldenrod) and I was thinking of a light colour for the front and a darker for the back and sides - wasn't sure what to do with the neck. The same as the body on the face of the headstock perhaps.Originally Posted by wokkaboy
- Sam
IB-5 - was finished, considering re-finishing body
IB-6S - done.
JR-1M - dressing frets and electronics build
ST-1 - still wondering how to install a tremelo
Telebass - non-PBG from parts buiild - painting body
Hi Sam, clear or top coat yes, but up to you. I put amber wudtone on mine and got good results so see how one coat looks on the cap.
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Beautiful cap Tindrrel! It's going to look great whatever you decide to do with it.
Funny because I was thinking of using the amber on the front, but the specs in the shop page say not to use on maple.
- Sam
IB-5 - was finished, considering re-finishing body
IB-6S - done.
JR-1M - dressing frets and electronics build
ST-1 - still wondering how to install a tremelo
Telebass - non-PBG from parts buiild - painting body
Sam, don't worry amber will soak into the cap fine. It's probably not as recommended to use on the tighter grain of the maple neck
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Is this the sort of top you apply any grain popping to? Is it likely to be thick enough veneer to sand back the dark dye?
- Sam
IB-5 - was finished, considering re-finishing body
IB-6S - done.
JR-1M - dressing frets and electronics build
ST-1 - still wondering how to install a tremelo
Telebass - non-PBG from parts buiild - painting body
If that's the look you're after this would be a perfect candidate. It's definitely possible to sand back the dye on the caps. Just don't over do it.
Posting Permissions
Reply With Quote