Page 2 of 5 FirstFirst 1 2 3 4 ... LastLast
Results 11 to 20 of 41

Thread: Brownsworthy's first! The DM -1S

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Member Brownsworthy's Avatar
    Join Date
    Nov 2017
    Location
    Newcastle
    Posts
    79
    Quote Originally Posted by wokkaboy View Post
    BW one of the pics looks like the frets are sitting in the slots ok and it's touching the fingerboard.

    Maybe check the fret ruler on another guitar to check the ruler is ok.

    Once we establish the scale length we can check the fret distances using the link below

    https://www.stewmac.com/FretCalculator
    The pic where it seems to be sitting in the slots ok is the 25.5 inch scale it hits the 7th fret and from there down is out on 24.75, what it should be it hits at the 5th fret and from there down is out.

  2. #2
    GAStronomist wokkaboy's Avatar
    Join Date
    Dec 2012
    Location
    Perth WA
    Posts
    13,555
    @ Franky looks like there is a slot for the nut if you look at the opposite side of the ruler, so it probably looks like its sitting ontop of the nut.
    Current Builds and status
    scratch end grain pine tele - first clear coat on !
    JBA-4 - assembled - final tweaks
    Telemonster double scale tele - finish tobacco burst on body and sand neck

    Completed builds
    scratch oak.rose gum Jazzmaster - assembled needs setup
    MK-2 Mosrite - assembled - play in
    Ash tele with Baritone neck - neck pup wiring tweaks and play in

  3. #3
    GAStronomist FrankenWashie's Avatar
    Join Date
    Jan 2016
    Location
    Glebe, NSW
    Posts
    5,666
    Quote Originally Posted by wokkaboy View Post
    @ Franky looks like there is a slot for the nut if you look at the opposite side of the ruler, so it probably looks like its sitting ontop of the nut.
    @wokka, yeah i see what you're saying, but on all of the necks i've tested mine on, F or G scales, you need to line that end notch up over the first fret. Maybe i do have a Dud rule? If i do as BW is doing, i get the same result, if i put that very end notch over the first fret, all the slots line up over the frets all the way down.
    FrankenLab
    Hand crafting guitars, because Death Rays are expensive.


  4. #4
    Member Brownsworthy's Avatar
    Join Date
    Nov 2017
    Location
    Newcastle
    Posts
    79
    Nope, I'm a GOOSE! Bah hahaha

    Frankie is spot on. I watched a YouTube video of a bloke with a rule that went to the nut and, when I checked mine, instantly assumed there was an issue with the guitar or rule. As it turns out the only issue was the fool trying to use the tool he does not know how to use!

    Thanks heapsfor your help Wokka and Frankie and I'm terribly sorry for wasting your time. If anything I hope you got a good laugh out of it I did.
    Last edited by dingobass; 06-12-2017 at 03:49 PM.

  5. #5
    GAStronomist FrankenWashie's Avatar
    Join Date
    Jan 2016
    Location
    Glebe, NSW
    Posts
    5,666
    Quote Originally Posted by Brownsworthy View Post
    Nope, I'm a GOOSE! Bah hahaha

    Frankie is spot on. I watched a YouTube video of a bloke with a rule that went to the nut and, when I checked mine, instantly assumed there was an issue with the guitar or rule. As it turns out the only issue was the fool trying to use the tool he does not know how to use!

    Thanks heapsfor your help Wokka and Frankie and I'm terribly sorry for wasting your time. If anything I hope you got a good laugh out of it I did.
    All good bud, it’s what the forum is here for. It’s not like you did anything really stupid like, strip the fretboard and reshape the tenon on your EXA kit, screw the Dingo tone coats up four times, and wire your emgs the wrong way around.
    FrankenLab
    Hand crafting guitars, because Death Rays are expensive.


  6. Liked by: Brownsworthy

  7. #6
    Moderator Brendan's Avatar
    Join Date
    Apr 2013
    Location
    Perth, WA
    Posts
    3,444
    Quote Originally Posted by FrankenWashie View Post
    All good bud, it’s what the forum is here for. It’s not like you did anything really stupid like, strip the fretboard and reshape the tenon on your EXA kit, screw the Dingo tone coats up four times, and wire your emgs the wrong way around.
    Or drop your finished body before wiring it up and attaching the neck 90cm onto concrete. All been there .

  8. Liked by: Brownsworthy

  9. #7
    Member Brownsworthy's Avatar
    Join Date
    Nov 2017
    Location
    Newcastle
    Posts
    79
    With the bridge in place, it's a non intonatable bridge, D was 627mm and G was 630mm. I also measured to the center of brige posts and they were both 628mm.

  10. #8
    GAStronomist wokkaboy's Avatar
    Join Date
    Dec 2012
    Location
    Perth WA
    Posts
    13,555
    ok BW that is definitely a 24.75" scale length so plug that into the Stewmac fret calculator (628.65mm) and enter number of frets (assume 22 frets). Pretty sure I remember Dedman's DM-1S build being 24.75" scale length
    Current Builds and status
    scratch end grain pine tele - first clear coat on !
    JBA-4 - assembled - final tweaks
    Telemonster double scale tele - finish tobacco burst on body and sand neck

    Completed builds
    scratch oak.rose gum Jazzmaster - assembled needs setup
    MK-2 Mosrite - assembled - play in
    Ash tele with Baritone neck - neck pup wiring tweaks and play in

  11. #9
    Member Brownsworthy's Avatar
    Join Date
    Nov 2017
    Location
    Newcastle
    Posts
    79
    Just measured all the frets with the figures that the stewmac calculator gave me and they're all pretty much spot on.
    So it seems that it is the straight rule that is out as it doesn't fit from the 5th fret down and as you get down to the higher frets it gets to the point where, at the 9th fret it is sitting in the middle of the high side in between the notches.

  12. #10
    GAStronomist wokkaboy's Avatar
    Join Date
    Dec 2012
    Location
    Perth WA
    Posts
    13,555
    I thought it may be the fret ruler. Maybe you can check the measurements of the slots by measuring front of the nut slot to front of all the other slots. I would ask for an exchange or a refund on your fret ruler must be a dodgy knock off
    Current Builds and status
    scratch end grain pine tele - first clear coat on !
    JBA-4 - assembled - final tweaks
    Telemonster double scale tele - finish tobacco burst on body and sand neck

    Completed builds
    scratch oak.rose gum Jazzmaster - assembled needs setup
    MK-2 Mosrite - assembled - play in
    Ash tele with Baritone neck - neck pup wiring tweaks and play in

Page 2 of 5 FirstFirst 1 2 3 4 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •