Yes the strongest one has a heavy duty umbrella stand as a base, ways a ton :P
Type: Posts; User: Froffy
Yes the strongest one has a heavy duty umbrella stand as a base, ways a ton :P
Great advice thanks.
I think now i might do the grain filling x2 and sanding sealer ,up until the paint stage and then glue the neck.
And yes i did read that the titebond 2 and 3 were not suitable...
Great thankyou for the info, i think ill leave the pick ups as is just incase.
Also my other kits were bolt on, should i glue this neck on before or after starting the project?
And ive read that...
Hi looking to start my Rcm-1 which will be my third Pitbull guitar the first 2 being the sta-1 and the tl-1 .
In regards to the body im going to grain fill, then sanding sealer the back before a...
Hi , i was thinking of painting it a burst of some sort and thought it may look wrong if i didnt fill/round off.....but now im thinking i may leave it and do it a solid colour
Hi, i got a RC-1 for xmas, just looking at the top side of the body down the bottom ( where the trapeze would go) see pic.
Has anyone done one of these kits? And if so do you round the edges (red...
Hi,
The reason i doubled up is because i miss read the diagram, i have now gone thru on both guitars checked everything, and also grounded from bridge to volume pot, and removed the doubled up wire....
Ok great thanks .
Yes there is a hole for the ground wire in the body.
And also as i already have a few wires grounded to the back of my volume pot, can i conect the bridge ground to the ground of...
HI, i should have put in my post, that i was reading you need to scratch the chrome off, as its vey hard to solder to chrome and you need the bare metal for it to adhere .
Also in regards to the ST-1, when connecting the ground to the bridge plate ( i have a hardtail bridge so no trem) it is chrome plated, do i have to scratch the chrome off before soldering? Or can i...
Hi just another question,
Looking at my bridge pickup on another guitar a TL-1 kit.
I replaced the bridge pickup with a fender one, underneath it has a blue ground wire that goes to a little plate...
Awesome , giving it a go now .
Thanks all most helpful.
Mark
pic of ground purple arrow
32940
Great thankyou, i think i will now start from all new.
Also i noticed on the north and south of the switch from the factory there is a terminal that is wired to ground , do i replicate this on...
Pic of wiring from factory
32938
Excellent thankyou, much appreciated.
I was just looking at the wiring that came from the factory and was thinking i can unsold-er all the pick up and second tone pot wires,and wire the new...
Also do i have to run the main ground wire to the bridge plate? or can i run it to where the spring on a humbucker screw sits , as the underside of my pick guard is shielded?
I put an arrow where the wire is. I imagine that one is to tell the switch to operate both volume and tone ,where as the link your talking about is to complete the circuit? .
32936
Thats great info , thankyou for clarifying that for me.
In regards to the link between the volume and tone pots, do i run the connecting wire from the solder points on the back of each pot where...
I cant seem to get a image to upload but this is the 3 way switch...
Hi, i have built the ST-1.
I have bought a seymour duncan trembucker TB-59 tb, and a diamazio super 2 distortion to replace the pickups
and also have bought a 3 way blade switch to replace the 5...
Oh and also if i find im terrible at shaping does the headstock shaping service still exist?
Hi , im currently saving up for one of the es-1tl kits https://www.pitbullguitars.com/shop/guitars/pit-bull-guitars-es-1tl-electric-guitar-kit/.
I was wondering if a non reverse firebird head...