Search:

Type: Posts; User: wschwisow

Search: Search took 0.00 seconds.

  1. You were right! I did a bit more research on...

    You were right! I did a bit more research on YouTube, then looked at the jack on my PRS and I see I had them reversed. Just swapped them back and it sounds great! Thanks for the response. I'll leave...
  2. Horrible noise when I plug in. Suggestions?

    So I just finished my first ever build. Really happy with the end result. Until I plugged it in. It's just a horrible loud buzzing noise. I'm new to this and only soldered 3 wires. I used my...
  3. Replies
    23
    Views
    32,332

    Looks fantastic! Nice job. I finished mine today....

    Looks fantastic! Nice job. I finished mine today. I'm in Seattle, USA so I went with a Seattle Sounders color scheme that's similar to yours. I'm really happy with this guitar EXCEPT when I plugged...
  4. Replies
    18
    Views
    14,929

    FINISHED!! The Floyd Rose took a while to set...

    FINISHED!!

    The Floyd Rose took a while to set up going back and forth but works fine now. Not sure what I've messed up with the wiring but it sounds like hell when I plug it in. Just loud noise. I...
  5. Replies
    18
    Views
    14,929

    Final buff and polish done. Bolt-on neck...

    Final buff and polish done. Bolt-on neck attached, Grover locking tuners installed and copper tape put in all the cavities.

    39365

    39366
  6. Replies
    2
    Views
    5,343

    Thank you so much! I'll try that out.

    Thank you so much! I'll try that out.
  7. Replies
    2
    Views
    5,343

    Sc-1 wiring help

    Hello. I am at the stage where I'm ready to start the final assembly but I'm very new to the wiring end of things. Here is a link to the SV-1 wiring diagram:...
  8. Replies
    18
    Views
    14,929

    I ended up with about 5-6 coats of Crystalac...

    I ended up with about 5-6 coats of Crystalac Brite Tone and let it cure for a little over a week. I then wet sanded with 1200 grit sandpaper and I'm on to the final polish and buffing stage. I think...
  9. Replies
    18
    Views
    14,929

    I think I ended up with 5-6 coats of Crystalac...

    I think I ended up with 5-6 coats of Crystalac Brite Tone top coat at this point. I'll let it sit and cure for a week or so before level sanding and final buffing.

    39183

    39184
  10. Replies
    18
    Views
    14,929

    2 coats of sanding sealer down. 2 more tomorrow....

    2 coats of sanding sealer down. 2 more tomorrow.
    39037
  11. Hmmm. I added dye to the first coat of grain...

    Hmmm. I added dye to the first coat of grain filler when I applied it to darken the deeper parts of the grain. After sanding most of it off I moved onto the staining. I was under the impression...
  12. Another question gentlemen... I added one coat of...

    Another question gentlemen... I added one coat of clear grain filler when I was happy with the overall color. I thought it best to do a light sand before a second coat. I used a fine P500 grit (maybe...
  13. Replies
    18
    Views
    14,929

    After a bit of touch up, I've add 2 coats of...

    After a bit of touch up, I've add 2 coats of clear wood grain filler. When this dries I'll spray 3-4 coats of sanding sealer and then on to the final top coat!
    39020
  14. Replies
    18
    Views
    14,929

    Very close now to being happy and moving on to...

    Very close now to being happy and moving on to the clear coating...
    39001
  15. Thanks for the suggestions gents. I'll see if I...

    Thanks for the suggestions gents. I'll see if I can sand back the areas and re-stain those spots.
  16. Replies
    18
    Views
    14,929

    Thanks, it's getting there.

    Thanks, it's getting there.
  17. Spots not taking stain very well...solutions?

    Hello all, I have a few spots that don't seem to want to accept the stain. I used a grain filler with a dark tint as my first coat, then sanded most of it away to create some contrast in the grain....
  18. Replies
    18
    Views
    14,929

    Toning down the yellow a bit and adding the dark...

    Toning down the yellow a bit and adding the dark blue in the neck area.

    38973

    38974
  19. Replies
    18
    Views
    14,929

    And on to the staining! 38958 38956 38957

    And on to the staining!

    38958
    38956
    38957
  20. Replies
    18
    Views
    14,929

    A few pics of the progress so far... 38953...

    A few pics of the progress so far...

    38953
    38954
    38955
  21. Replies
    18
    Views
    14,929

    Wayne's First Build - The SV-1

    Hello everyone. So excited to be part of this community. I received my SV-1 last week and started on it today. I put up a build log on an old website i don't use much anymore. I'll be posting along...
  22. Replies
    23
    Views
    32,332

    Hey Greg, I am getting my SV-1 today (Christmas...

    Hey Greg, I am getting my SV-1 today (Christmas gift also) and it's my first ever build. I'll be learning from your progress! Looking good!
Results 1 to 22 of 22