Search:

Type: Posts; User: Rabbit

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    147

    If you are handy with the computer you might want...

    If you are handy with the computer you might want to consider tracing the template onto a vector program and resizing it to fit the tuner holes of the PB headstock..
  2. Replies
    9
    Views
    278

    Doesn't it involve tossing your tools in to a...

    Doesn't it involve tossing your tools in to a couple of draws?
  3. Replies
    16
    Views
    463

    Aren't tools consumables? Don't you use them once...

    Aren't tools consumables? Don't you use them once or twice then throw them away to buy new, better shiny ones? ;)
  4. Replies
    17
    Views
    394

    Black shows up imperfections. Gloss black shows...

    Black shows up imperfections. Gloss black shows up *every* imperfection :rolleyes: !
  5. Replies
    17
    Views
    394

    .....cause your friends don't have a sea foam...

    .....cause your friends don't have a sea foam green guitar and if they don't have a sea foam green guitar then they're no friends of mine.....
  6. Replies
    41
    Views
    15,320

    All depends on which paint you use, and which...

    All depends on which paint you use, and which mask ;) .Next is the silver, and maybe the bevel shadow. Not all the axe bases have the shadow on the bevel of the blade, nor the outline of the body.
  7. Replies
    17
    Views
    394

    Neon pink candy!

    Neon pink candy!
  8. If painting you don't wanna above 240 grit. Just...

    If painting you don't wanna above 240 grit. Just make sure it's smooth and with 240 grit there shouldn't be any obvious sanding marks.You can use a primer to fill the grain and sand smooth.The paint...
  9. For pre paint, I would not go any finer than 240...

    For pre paint, I would not go any finer than 240 grit. On timber that gives a fairly smooth. Go too fine and you end up burnishing the timberand compromising the surface for paint to grip to.1500grit...
  10. Replies
    22
    Views
    6,218

    Yes I did paint those. and the Tower *case*...

    Yes I did paint those. and the Tower *case* contains a computer with two hard drives I was given the empty case and had to completely dismantle it, strip it back to bare metal, cold gal the inside,...
  11. Replies
    22
    Views
    6,218

    Essentially the same as staining. These candies...

    Essentially the same as staining. These candies are not different to a stain, but in a pint system they are mixed with a clear carrier, in this case clear coat. The candies as are could probably be...
  12. Replies
    22
    Views
    6,218

    Depending on the effect you want, a strait up...

    Depending on the effect you want, a strait up candy requires no base. A metalic silver gives a nice effect:
    ...
  13. Replies
    22
    Views
    6,218

    Well with another 2 weeks lock down I can't get...

    Well with another 2 weeks lock down I can't get to my neckthrough blank or wing timber, I still need to order pots and caps, and two of the tuners are still being manufactured. But I did get some...
  14. Replies
    154
    Views
    22,945

    And for some reason I cannot help but be reminded...

    And for some reason I cannot help but be reminded of Simon's comment on another thread describing the body design as looking "excited" .....
  15. Replies
    154
    Views
    22,945

    I take it a razor blade and some sanding of the...

    I take it a razor blade and some sanding of the runs before another coat of yellow?
  16. Replies
    17
    Views
    633

    Or sand down till flat and leave smooth with no...

    Or sand down till flat and leave smooth with no polishing so that it doesn't stick to your hand ;)
  17. Replies
    154
    Views
    22,945

    Is that the canary in the coal mine?

    Is that the canary in the coal mine?
  18. Thread: Mystery bits

    by Rabbit
    Replies
    9
    Views
    432

    I think it comes down to ease of use and many...

    I think it comes down to ease of use and many find the gun stock finish "good enough". A wipe on urethane is probably just as easy to apply.
  19. Replies
    35
    Views
    1,169

    Using the appropriate blade for the material. In...

    Using the appropriate blade for the material. In some cases, such as ripping blades such as 24 tooth or coarser blade on a 10 inch/254mm, there are so called "glueline" blades intended to give a...
  20. Replies
    35
    Views
    1,169

    You don't "need" a jointer for stuff like that....

    You don't "need" a jointer for stuff like that. Many manage just fine with either the right blade on a table saw /circular saw, or failing that, a jointing plane. If you realy feel the need for power...
  21. Replies
    16
    Views
    7,054

    With enough coats you should have no problems...

    With enough coats you should have no problems sanding level and then buffing and polishing.
  22. Replies
    16
    Views
    7,054

    Replace "paint" with "creosote" hehe.. Talk about...

    Replace "paint" with "creosote" hehe.. Talk about overspray! We did try it with paint on the decking...yeh, not good!



    You can get a reasonable compressor suitable for small stuff like guitars...
  23. Replies
    6
    Views
    405

    You may want to check what the internal structure...

    You may want to check what the internal structure of those pups are. Some soap bars have a long mag across the poles and some have individual pole pieces, all hidden under the cover. A 5 sting pup...
  24. Replies
    16
    Views
    7,054

    Don't know about the Ozito gun, but I have used a...

    Don't know about the Ozito gun, but I have used a Wagner in the past. I realy hope they have improved, because they were pretty crap. You may be able to spray stain, but top coating was never going...
  25. Replies
    39
    Views
    2,114

    I think the whole active thing is just a...

    I think the whole active thing is just a perceived difference. any circuit you can crowbar into the instrument can be stuffed into the amp or a pedal. A bass is already heavy, why add extra weight?...
Results 1 to 25 of 269
Page 1 of 11 1 2 3 4