Search:

Type: Posts; User: Froffy

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    10,526

    Yes the strongest one has a heavy duty umbrella...

    Yes the strongest one has a heavy duty umbrella stand as a base, ways a ton :P
  2. Replies
    6
    Views
    10,526

    Great advice thanks. I think now i might do the...

    Great advice thanks.
    I think now i might do the grain filling x2 and sanding sealer ,up until the paint stage and then glue the neck.
    And yes i did read that the titebond 2 and 3 were not suitable...
  3. Replies
    6
    Views
    10,526

    Great thankyou for the info, i think ill leave...

    Great thankyou for the info, i think ill leave the pick ups as is just incase.
    Also my other kits were bolt on, should i glue this neck on before or after starting the project?
    And ive read that...
  4. Replies
    6
    Views
    10,526

    Rcm-1 A few questions

    Hi looking to start my Rcm-1 which will be my third Pitbull guitar the first 2 being the sta-1 and the tl-1 .

    In regards to the body im going to grain fill, then sanding sealer the back before a...
  5. Replies
    2
    Views
    3,458

    Hi , i was thinking of painting it a burst of...

    Hi , i was thinking of painting it a burst of some sort and thought it may look wrong if i didnt fill/round off.....but now im thinking i may leave it and do it a solid colour
  6. Replies
    2
    Views
    3,458

    RC-1 shaping question

    Hi, i got a RC-1 for xmas, just looking at the top side of the body down the bottom ( where the trapeze would go) see pic.

    Has anyone done one of these kits? And if so do you round the edges (red...
  7. Hi, The reason i doubled up is because i miss...

    Hi,
    The reason i doubled up is because i miss read the diagram, i have now gone thru on both guitars checked everything, and also grounded from bridge to volume pot, and removed the doubled up wire....
  8. Ok great thanks . Yes there is a hole for the...

    Ok great thanks .
    Yes there is a hole for the ground wire in the body.
    And also as i already have a few wires grounded to the back of my volume pot, can i conect the bridge ground to the ground of...
  9. HI, i should have put in my post, that i was...

    HI, i should have put in my post, that i was reading you need to scratch the chrome off, as its vey hard to solder to chrome and you need the bare metal for it to adhere .
  10. Also in regards to the ST-1, when connecting the...

    Also in regards to the ST-1, when connecting the ground to the bridge plate ( i have a hardtail bridge so no trem) it is chrome plated, do i have to scratch the chrome off before soldering? Or can i...
  11. Hi just another question, Looking at my bridge...

    Hi just another question,
    Looking at my bridge pickup on another guitar a TL-1 kit.
    I replaced the bridge pickup with a fender one, underneath it has a blue ground wire that goes to a little plate...
  12. Awesome , giving it a go now . Thanks all most...

    Awesome , giving it a go now .
    Thanks all most helpful.
    Mark
  13. pic of ground purple arrow 32940

    pic of ground purple arrow
    32940
  14. Great thankyou, i think i will now start from all...

    Great thankyou, i think i will now start from all new.

    Also i noticed on the north and south of the switch from the factory there is a terminal that is wired to ground , do i replicate this on...
  15. Pic of wiring from factory 32938

    Pic of wiring from factory

    32938
  16. Excellent thankyou, much appreciated. I was...

    Excellent thankyou, much appreciated.

    I was just looking at the wiring that came from the factory and was thinking i can unsold-er all the pick up and second tone pot wires,and wire the new...
  17. Also do i have to run the main ground wire to the...

    Also do i have to run the main ground wire to the bridge plate? or can i run it to where the spring on a humbucker screw sits , as the underside of my pick guard is shielded?
  18. I put an arrow where the wire is. I imagine that...

    I put an arrow where the wire is. I imagine that one is to tell the switch to operate both volume and tone ,where as the link your talking about is to complete the circuit? .


    32936
  19. Thats great info , thankyou for clarifying that...

    Thats great info , thankyou for clarifying that for me.

    In regards to the link between the volume and tone pots, do i run the connecting wire from the solder points on the back of each pot where...
  20. I cant seem to get a image to upload but this is...

    I cant seem to get a image to upload but this is the 3 way switch...
  21. Help with wiring trembucker and super 2 distortion in ST-1

    Hi, i have built the ST-1.
    I have bought a seymour duncan trembucker TB-59 tb, and a diamazio super 2 distortion to replace the pickups
    and also have bought a 3 way blade switch to replace the 5...
  22. Replies
    3
    Views
    30,261

    Oh and also if i find im terrible at shaping does...

    Oh and also if i find im terrible at shaping does the headstock shaping service still exist?
  23. Replies
    3
    Views
    30,261

    Template for a non reverse firebird headstock

    Hi , im currently saving up for one of the es-1tl kits https://www.pitbullguitars.com/shop/guitars/pit-bull-guitars-es-1tl-electric-guitar-kit/.

    I was wondering if a non reverse firebird head...
Results 1 to 23 of 23