Waz's MMB-4

Printable View

Show 40 post(s) from this thread on one page

11-02-2018, 04:50 PM
Andy40

I think its nice and toasty Waz ;)
11-02-2018, 04:55 PM
JohnH

Man, that looks great. For some reason I didn't think you could use Meguiars, etc on TO finishes. Good to know
11-02-2018, 04:57 PM
wazkelly

5 Attachment(s)

Attachment 24735 Attachment 24736 Attachment 24737 Attachment 24738 Attachment 24739
11-02-2018, 04:58 PM
wazkelly

Quote:

Originally Posted by Andy40

I think its nice and toasty Waz ;)

Thanks Andy
11-02-2018, 05:02 PM
wazkelly

Quote:

Originally Posted by JohnH

Man, that looks great. For some reason I didn't think you could use Meguiars, etc on TO finishes. Good to know

Hi John, guilty as charged your honour - I have used TO on all 6 builds with Meguairs as the main polishing agent used after doing the micro mesh wet sanding. On the Swampcaster I also experimented with Brasso and Nu Finish.

Brasso is very abrasive for a liquid polish and is good for stripping back lumpy bits which quite often occur when ragging on TO, particular in hot or humid conditions. Nu Finish is like the fine scratch stuff some other folk use and just adds that little bit more mirror like zing.
11-02-2018, 05:06 PM
JohnH

Quote:

Originally Posted by wazkelly

Hi John, guilty as charged your honour - I have used TO on all 6 builds with Meguairs as the main polishing agent used after doing the micro mesh wet sanding. On the Swampcaster I also experimented with Brasso and Nu Finish.

Brasso is very abrasive for a liquid polish and is good for stripping back lumpy bits which quite often occur when ragging on TO, particular in hot or humid conditions. Nu Finish is like the fine scratch stuff some other folk use and just adds that little bit more mirror like zing.

I'll have to give them a crack on my LP build. If I get mine looking even half as nice as yours, I'll be happy!
11-02-2018, 05:07 PM
wazkelly

4 Attachment(s)

Time to start getting ready to install the electronics....
Attachment 24741 Attachment 24742 Attachment 24743 Attachment 24744
11-02-2018, 05:15 PM
wazkelly

Quote:

Originally Posted by JohnH

I'll have to give them a crack on my LP build. If I get mine looking even half as nice as yours, I'll be happy!

Hi John, the trick is to have lots of thin TO coats to work with. Suggest laying 4-6 thick ones, light 1500 wet sand, then 6 - 8 coats diluted 50/50 with turps, another 1500 wet sand, same again and then step up to 2000 grit for the next wet sand. If all looks nice and flat, go for gold with the micro mesh pads and then start with Meguiars.

Every now and then you may burn through too much and thankfully TO is quite forgiving in applying small touch ups that can be easily blended into the existing finish with a bit of patience and finesse.

Lost count how many coats this one has....probably 30 or 40 and have 2 minor spots that need a bit more TO as the final polish just started to go too deep in those places.
10-04-2018, 04:43 AM
blinddrew

Started reading this thread thinking, "Ah, this looks like the kind of finish I have in mind."
I'm now thinking I may have just ordered an expensive box of firewood!
That looks fantastic. :)
10-04-2018, 10:19 AM
wazkelly

Thanks Blinddrew.

Most things can be recovered somewhat with a bit of patience.

On this one I am still carefully working on the few spots where polish went too deep. Might take another week or so before it is ready for final assembly.

Cheers, Waz

Sent from my SM-A520F using Tapatalk

Show 40 post(s) from this thread on one page