JM-1 Help

I'm a newbie building my first jm-1.
I'm struggling with an incorrect wiring diagram, however, don't believe it should be that difficult.
I have four wires ( Green, red, Orange and yellow ).I have the black but know what thats for.
The four wires I believe, tell me if I'm wrong, need to be soldered to the 5 way switch and I'm not sure what goes where.

Hoping someone can help me a trip to the music shop!

Cheers

This thread about JM-1 wiring may help. Hopefully, your layout looks something like this:

http://pitbullguitars.com/wp-content...8/1spkd-jm.jpg

It looks like you should have a black ground wire that connects to the tremolo/bridge to the back of a tone pot. Then, you should need to connect an output wire from the switch to the volume pot, and then separate wires from the switch to each tone pot. You should also connect a ground wire from the pickup grounds (negatives) at the switch (ground lug) to the common ground point on the back of the vol/tone pot. Although this diagram has a single coil bridge pickup and your switch position is different, the basic wiring layout should match what you need:

http://pitbullguitars.com/wp-content...ratImport2.jpg


Does that help?

Massive Help... Thanks

Timing is everything. I am almost at the stage of wiring up my JM and now I don't need to go hunting. Thanks man!

Yeah really big help.

I, like Coriem am also a newbie building my first JM-1. That wiring diagram was a big help. I was wondering if anyone could assist with an issue I have been having with attaching the bridge. The two bolt holes that came already drilled into the body seem too close to the hole where the bridge is supposed to be input. I have inserted the bolts that the bridge sits up against, however, when it comes to putting in bridge piece, it won't fit…

So I guess my questions are as follows:
- How likely is it that the bolt holes and the bridge hole have been incorrectly drilled by the factory that makes these guitar parts?
- Should the bridge fit in easily against the bolts, and in fact have some slack?
- Also, do the bolts need to be hammered in flush against the body of the guitar?

Any help would be great.

Cheers

Hi Charles.
I had a few little 'imperfections' with the bridge arrangement on my JM build too. The biggest one being that the post holes were not deep enough to allow the post to be flush when hammered in. So check that. As for your issues, I can't quite visualise what you're saying. Any chance of posting a picture?
Cheers

OK,
Firstly, dont hammer the bushings in! You are better to press them in with a large g clamp or a drill press..
If you dont have access to either then very gently tap them in using a block of timber to protect the bushings.

Next up, screw the bolts in about a quarter of the way, so they still has a little bit of wobble. the bridge should then slip on.

Then with a large screw driver you should be able to lower the bridge to the correct height when you do your set up :)

Hey thanks for the quick reply guys,

Unfortunately I am at work right now so I can't upload any pictures, though I will do that tonight Lawry.

Hey Dingobass - ok so I won't hammer them in, but they currently won't sit flush with the guitar body so perhaps I need to drill a little bit more so they can easily get deep enough...? Also, I have tried what you suggested about only screwing the bolts in about a quarter of the way, however, the bridge will not slip in. I have also tried putting the bridge in one bolt at a time, however in this situation I encounter two problems:
1.) When screwing in the second bolt, as the bridge is so tight against the bolts, instead of pulling the bridge down onto the guitar, the bushing lifts out of the guitar.
2.) When I did manage to get the bridge as far down as possible, it is so tight up against the bolts that if I were to attach the tremolo bar, there is no way that the bridge would lift up and down...

What I was thinking of doing is filing down the hole (where the bridge goes) toward the bottom of the guitar body so the bridge can move about more freely once in the hole.

Will upload some photos tonight, though would really appreciate some more help.

should be able to work out a solution Charles once we see some photos.
Take some above and below photos so its clear

\\\\uds\\5\\cslessar\\Desktop\\guitar 1.jpg

Alright so I've measured it and it is 7mm from the bridge hole to the edge of the bolt holes