PDA

View Full Version : ST-1



DanMade
26-08-2013, 04:16 AM
ST-1 finished in Wudtone Amber.
Gotoh tuners
Wilkinson tremolo
GFS single coils
Push pull pot for neck on switch
Treble bleed mod
Vaneered scratch plates
http://pitbullguitars.com/wp-content/uploads/2013/08/w3nh7-image.jpg
http://pitbullguitars.com/wp-content/uploads/2013/08/v84kx-image.jpg
http://pitbullguitars.com/wp-content/uploads/2013/08/7l98n-image.jpg

adam
26-08-2013, 06:46 AM
ST-1 in Wax Finish. Built by Dingobass.

Upgraded scratch plate, pickups, switch and knobs.


http://pitbullguitars.com/wp-content/uploads/2013/08/hm74f-SNGK001.jpg

robin
26-08-2013, 07:51 AM
ST-1

Jarrah Stain with Tru-Oil finish
Black Scratch Plate
Tonerider City Limits Pickups
7 Sound wiring mod
Treble Bleed mod
http://pitbullguitars.com/wp-content/uploads/2013/08/px840-FG_028-2.JPG
http://pitbullguitars.com/wp-content/uploads/2013/08/gaz3r-B_020-2.JPG
http://pitbullguitars.com/wp-content/uploads/2013/08/u0h63-B_025.JPG

wokkaboy
27-08-2013, 01:24 AM
ST-1 in surfer girl wudtone, all parts stock
http://pitbullguitars.com/wp-content/uploads/2013/08/063i2-Surfer-Girl-Close-Front.jpg
http://pitbullguitars.com/wp-content/uploads/2013/08/3v97o-Surfer-Girl-Front.jpg
http://pitbullguitars.com/wp-content/uploads/2013/08/9hq14-Surfer-Girl-Back.jpg

wokkaboy
27-08-2013, 01:27 AM
ST-1 in black magic woman wudtone, water droplet effect on scratchplate, all parts stock
http://pitbullguitars.com/wp-content/uploads/2013/08/82esf-BMW-strat.JPG
http://pitbullguitars.com/wp-content/uploads/2013/08/r8wd7-Front-BMW-Strat.jpg
http://pitbullguitars.com/wp-content/uploads/2013/08/10k72-Back-BMW-Strat.jpg

robin
28-08-2013, 11:49 AM
Finish: Wudtone Carmine Gypsy
Neck and Headstock: Tru-oil
All Standard Parts
http://pitbullguitars.com/wp-content/uploads/2013/08/r9ydp-1009.JPG
http://pitbullguitars.com/wp-content/uploads/2013/08/vtwy0-014.JPG

jase
16-09-2013, 06:54 AM
ST-1 in Faded Fiesta. PBG stock
http://pitbullguitars.com/wp-content/uploads/2013/09/47736-image.jpg
http://pitbullguitars.com/wp-content/uploads/2013/09/m51j5-image.jpg

gavinturner
25-10-2013, 03:22 AM
ST-1 finished in Wudtone Surfer Girl 50% + T-Bird 50%.
All stock except Pearloid Scratchplate.


http://pitbullguitars.com/wp-content/uploads/2013/10/3u26j-IMG_2585_small.JPG

http://pitbullguitars.com/wp-content/uploads/2013/10/64gw2-IMG_2589_small.JPG

http://pitbullguitars.com/wp-content/uploads/2013/10/7y71q-IMG_2592_small.JPG

gavinturner
25-10-2013, 03:24 AM
more photos

http://pitbullguitars.com/wp-content/uploads/2013/10/1rezr-IMG_2591_small.JPG

http://pitbullguitars.com/wp-content/uploads/2013/10/25ypx-IMG_2567_small.JPG

johnandles
03-12-2013, 08:51 AM
My ST build.mods include, treble bleed,No load blender pot.replaced pickups and pearl scratch plate.
sounds great.
Finished in homebrew tru type oil plus bees wax
Cheers
john
http://www.pitbullguitars.com/wp-content/uploads/2013/12/y55u5-IMG_3731.JPG
http://www.pitbullguitars.com/wp-content/uploads/2013/12/d3ufd-IMG_3732.JPG

MetalMatt
02-01-2014, 03:33 AM
Wudtone Vintage Blonde
Vintage Amber neck
All parts stock Pitbull Guitars

http://img.photobucket.com/albums/v472/oldval/blondestrat/blondestrat.jpg

http://img.photobucket.com/albums/v472/oldval/blondestrat/blondestrat2.jpg

Dengreg
14-06-2014, 07:18 AM
Finished in Wudtone Surfer Girl
Standard except Graph Tech Tusq Nut.
http://www.pitbullguitars.com/wp-content/uploads/2014/06/2ol64-image.jpg
http://www.pitbullguitars.com/wp-content/uploads/2014/06/ewt7j-image.jpg
http://www.pitbullguitars.com/wp-content/uploads/2014/06/8i9q2-image.jpg

barrylicious
14-07-2014, 06:02 AM
This was done by my 11 yo nephew. With a little guidance. All drilling screwing painting cutting sanding sanding and sanding were done by him.
Needless to sAy I'm now his favorite uncle.
http://www.pitbullguitars.com/wp-content/uploads/2014/07/mls3y-image.jpg

andrewdosborne
30-07-2014, 09:52 AM
ST-1, all stock
Body Wudtone Azure Sky 50/50 with white base and high gloss finish with no ageing or tints
Neck Wudtone Vintage Amber

http://www.pitbullguitars.com/wp-content/uploads/2014/07/d54ys-ST-Full.jpg
http://www.pitbullguitars.com/wp-content/uploads/2014/07/j48mn-ST-Close.jpg

[Excuse the shadow..]
http://www.pitbullguitars.com/wp-content/uploads/2014/07/00p61-ST-Back.jpg

BUNDY
20-01-2015, 04:01 AM
Not quite finished.. I put a different neck on from an old cheap guitar because the stock one was loose, I can't wait to play this thing. 1447

Andy40
13-12-2015, 03:22 AM
Pitbull Guitars ST-1 Kit
Tonerider Pure Vintage Pickups
Pearloid Pickguard
Parchment volume, tone knobs and switch
Vintage Style Tuners
Bourns 250k Mini Pots
CLR 5 way switch
Vintage style cloth wiring
Lake Placid Blue Nitrocellulouse finish body
Clear '60's tint Nitrocellulouse finish neck
DB "F" Style Bone Nut
Switchcraft jack
the rest is Pitbull guitar standard
69816982698369846985

dave.king1
31-03-2016, 06:30 AM
The Count
All standard kit parts, acrylic yellow from Supercheap, FW maple stain ( from somewhere that must never be mentioned ) on the neck.

I'm about to take the neck off to get a better finish and do a full setup.

Dikkybee007
09-03-2017, 07:50 AM
1789317894178951789617897

I already have a strat so I wanted something a little different and seeing as I love the head shape and through body arrangement on tele's I thought I would combine both. I had to replace the first body as I had an oops moment converting to a through body so there was a bit of a delay and I was in a pickle about what colour so I put a bit of a stain on the neck but left the body natural and once I got it to where I wanted in by sanding and put about 7 thin coats of Tru-oil on with light sanding with 0000 steel wool between coats after the third just to level out any imperfections. Didn't want a high gloss and the final coat I just rubbed down with a very fine scotch-brite to remove some slight bumps but not enough to dull finish which left it smooth. Levelled frets and polished and used 2 good coats of almond oil on rosewood to protect wood, installed bone nut and Wilkinson tuners. I used a Kent Armstrong Motherbucker as I found the idea of being able to run in series,split and parallel novel but found the wiring was a nightmare until I got my head around it due to the lack of clear instructions. Have 1 volume to be used to roll off when played loud, or so the instructions say and have a Gibson styled switch with home made ally knob so I can have 1 or both coils running. Its not a show winner hence low quality pics but I thought someone might be interested and if someone wanted help with this sort of wiring I can help explain.

adam
23-06-2017, 05:22 PM
ST-1 with Carvings and Pyrography, by Frank

20191

DrNomis_44
23-06-2017, 09:34 PM
Thought that I would contribute a couple of pics of my Gold Strat STA-1M build, so here we go:

20193


And here's a closeup pic of the new Full Contact System bridge that I installed a few days ago, I know it's a silver one but I will be swapping it out for a gold one later on this year:

20194

Dedman
05-07-2017, 04:51 PM
It's black because that's what I do :)

Black Goto bridge, Black Grover tuners, Tonerider City Limits pick ups push pull pot on tone 1 "adds all" on on positions 2 and 4

20463

nitroburner1000
09-07-2017, 05:10 PM
Thought id post my Strat i did back in August

ST-1 By NitroBurner1000
Hi guys, this is my first build and with plenty of help from the guys here its finally finished.

Quick rundown..........
Aftermarket Pickguard to fit twin humbuckers, white pearloid
Seymour Duncan JB and Jazz HotRodded Humbuckers
Upgraded to Grover Tuners
Black hardware
Copper shielding to humbucker bays
3 aftermarket push pull pots to ...1) split the pups 2) series parallel options, 3) in and out of phase.
Vintage cloth wiring
Treble Bleed mod
Plastic nut replaced with a bone one
Replaced stock 5 way switch with 3 way.

PAINT FOR BODY....
6 coats sealer/primer,
6 coats of black basecoat,
4 coats of metallic undercoat and
6 topcoats of clear 1k acrylic full gloss.
Sanded between coats, bodyfilled and finally buffed and polished

NECK AND HEADSTOCK
Stained and finished off with wipe on poly.

20547 20548 20549

20550

nitroburner1000
09-07-2017, 05:13 PM
Update.... neck resanded and restained with a different stain. Logo removed, redo at a later date.

20551 20552 20553

Micko
03-07-2020, 06:02 AM
My second build st-1 with tone rider pickups and Grover tuners
Finished with black stain and Cromax 2 pack clear

madmikedynamite
04-01-2022, 02:58 AM
The Count
All standard kit parts, acrylic yellow from Supercheap, FW maple stain ( from somewhere that must never be mentioned ) on the neck.

I'm about to take the neck off to get a better finish and do a full setup.

Hi Dave on the off chance you are still on this forum what paint did you use from supercheap?

Cheers
Mike

dave.king1
04-01-2022, 12:58 PM
Hi Dave on the off chance you are still on this forum what paint did you use from supercheap?

Cheers
Mike

G'day Mike,

Still here but haven't built since the Tuff Dog Tele, as for the ST-1 I can't remember of it was Septone or SCA and a bright yellow acrylic and which ever it was I used the same brand undercoat and clear.

It's now got Tonerider Vintage Classics in place of the kit items and sounds great.

I've not held another PB ST but my one also has a chunky vintage fat neck, don't know if this is standard but I love it

madmikedynamite
18-01-2022, 03:20 AM
G'day Mike,

Still here but haven't built since the Tuff Dog Tele, as for the ST-1 I can't remember of it was Septone or SCA and a bright yellow acrylic and which ever it was I used the same brand undercoat and clear.

It's now got Tonerider Vintage Classics in place of the kit items and sounds great.

I've not held another PB ST but my one also has a chunky vintage fat neck, don't know if this is standard but I love it

Hey Dave,

It looks great, the black hardwear really goes well with the yellow. Did you use a spray gun or was it rattle cans?

cheers

Mike

dave.king1
20-01-2022, 10:00 PM
Rattle cans Mike

pr0jekt
25-07-2023, 06:15 PM
ST-1 by me, in Feast Watson Wipe on poly satin :)

44611

Jetblack
25-07-2023, 07:06 PM
Love that finish, black scratch guard and chrome screws really set it off.