PDA

View Full Version : Headstock Design



forthoseofus
29-12-2012, 02:34 AM
Hi all, just wondering what you think of the headstock design I am thinking about for my ST-1.

I saw this designhttp://www.flickr.com/photos/crimsonguitars/6950744312/in/photostream/ and liked it. For some reason I really liked the hole in the headstock.
I still wanted a place to put a string tree should I need it (I've got staggered tuners) so a direct copy of the design would not be suitable.

I came up with the following design
-An initial sketch, and
-a better one done on computer

Any one have any comments, or things to look out for in this design.
I'm going to be doing this with jigsaw, files, and good old fashion sandpaper, as those are pretty much all the tools I have available to me.

I might pickup a cheap piece of pine to practice on.
http://pitbullguitars.com/wp-content/uploads/2012/12/b6j3a-Headstock-Sketch.jpg
http://pitbullguitars.com/wp-content/uploads/2012/12/gxx1i-Headstock.jpg

29-12-2012, 03:43 AM
Quote from forthoseofus on December 28, 2012, 11:34
Hi all, just wondering what you think of the headstock design I am thinking about for my ST-1.


Ah, memories of the Floyd Rose headstock.

The Floyd Rose headstock was nothing more than an outline, but then, the strings stopped at the nut so they didn't put any tension on the headstock. Enough of the history lesson.

OK, the good news. Technically, you're not removing anywhere near enough material to affect the stability of the headstock, so go for it as designed.

(I'd only go as far as that in the photo if I had a solid and very stable piece of quartersawn timber. I'd err by 5% on the cautious side and more likely 10%. There's nothing worse than finishing it then finding you went to 101% of it's strength... :( - dingobass- your thoughts on requirements for a headstock like the photo?)

And the bad news- well, there ain't any bad news! :D It's your guitar and you want to do it, so do it. After all, that's why you're building a kit, not a buying a finished guitar.

I don't know how you are considering doing this, but a template and a router may be an option.

MikeL
29-12-2012, 04:04 AM
Don't mind it at all :) I even rendered it to give a better look at it for you ( low quality tho, I'm at work ;)
http://pitbullguitars.com/wp-content/uploads/2012/12/y5c8s-hd2.jpg
http://pitbullguitars.com/wp-content/uploads/2012/12/z8s4x-hd1.jpg

dingobass
29-12-2012, 08:20 AM
Quote from dmac on December 28, 2012, 12:43

Quote from forthoseofus on December 28, 2012, 11:34
Hi all, just wondering what you think of the headstock design I am thinking about for my ST-1.


Ah, memories of the Floyd Rose headstock.

The Floyd Rose headstock was nothing more than an outline, but then, the strings stopped at the nut so they didn't put any tension on the headstock. Enough of the history lesson.

OK, the good news. Technically, you're not removing anywhere near enough material to affect the stability of the headstock, so go for it as designed.

(I'd only go as far as that in the photo if I had a solid and very stable piece of quartersawn timber. I'd err by 5% on the cautious side and more likely 10%. There's nothing worse than finishing it then finding you went to 101% of it's strength... :( - dingobass- your thoughts on requirements for a headstock like the photo?)

And the bad news- well, there ain't any bad news! :D It's your guitar and you want to do it, so do it. After all, that's why you're building a kit, not a buying a finished guitar.

I don't know how you are considering doing this, but a template and a router may be an option.


I don't see any problems there :D

If it was a Bass headstock I would be a bit wary as the string tension is phenomenal compared to a guitar. :o

Another option for string trees is to use a retainer bar, they look a lot neater as you can install it closer to the nut.

29-12-2012, 01:17 PM
Quote from dingobass on December 28, 2012, 17:20

Another option for string trees is to use a retainer bar, they look a lot neater as you can install it closer to the nut.

I always put staggered Sperzel locking tuning machines on the table as an option, so you need no string retention whatsoever. I put them on the Telecowster years ago as an experiment and have never thrown a string. Or, come to think of it, broken one either.

I don't know if the Chinese copies have staggered heights. I doubt it.

dingobass
29-12-2012, 02:19 PM
Quote from dmac on December 28, 2012, 22:17

Quote from dingobass on December 28, 2012, 17:20

Another option for string trees is to use a retainer bar, they look a lot neater as you can install it closer to the nut.

I always put staggered Sperzel locking tuning machines on the table as an option, so you need no string retention whatsoever. I put them on the Telecowster years ago as an experiment and have never thrown a string. Or, come to think of it, broken one either.

I don't know if the Chinese copies have staggered heights. I doubt it.

I have seen Chinese copies of staggered Sperzels, but..... Why buy copies? Been down that path with the Axe of Destiny. Got a copy Floyd Rose and, well, it will be replaced with the real thing in the near future... You get what you pay for... :?

MikeL
16-04-2013, 09:04 AM
This is what I did with my ST-1 head ( Guitar should be completed this month :) )

http://www.dark-castle.org.au/pitbull/11.jpg


http://www.dark-castle.org.au/pitbull/15.jpg

17-06-2013, 06:47 AM
Love the paint job, ended up looking pretty slick!

Bass Guy
17-06-2013, 08:36 AM
This is looking awesome! Right up my street!

rhay
17-06-2013, 10:00 AM
Certainly a really original design. To my eye the finished piece looks much better than the original sketch - really good execution.

Scott J.
09-07-2013, 11:51 AM
QUESTION?

Headstocks (on the SG-1 & ES-1G) - its a bit hard to tell from the photos of the kits but I was wondering if the size of the blank headstock permits the "wider" Gibson-style sized headstock to be cut from the blank rather than the narrower Epiphone-style headstock?

Keep on rockin'
Scott J.

02-09-2013, 12:51 AM
hello, I have an LP-1m kit and have chosen to do a Gibson design I have traced the shape on the top of the headstock just wondering what is the best method to cut out the headstock without damaging the wood?

Thanks guys

dingobass
02-09-2013, 05:33 AM
If you have a jig saw, tape the back of the headstock and use a fine toothed blade.
Then do the final shaping with a half round bastard file then sandpaper.

02-09-2013, 06:09 AM
Ok great thanks very much Db much appriciated :)