PDA

View Full Version : Build 2 - hollow body



GavinPinksterboer
19-09-2020, 02:45 PM
Build 1 has been put to the side in mild disgrace so I can contemplate it’s future , press on or sand back.... got the poly on with a coat every day this week. Had a couple of little runs near the edge. So wet sanded 1000, and went through......

So thought we’d start a harder build and see how that goes...

Going pretty well so far. Rubbed back 240 and tried to highlight the grain with metho-diluted fw prooftint black, tried a burst outline . rubbed back again at 240 then tried rustoleum barn red stain over the top. Not keen on this as it’s a bit sticky and yuck but I’ve been waiting a month so far for keda dyes so that’s what I could get ...

Neck sanded 240 and stained golden teak https://uploads.tapatalk-cdn.com/20200919/f2c5a038716c92492d55f08e2880f50e.jpg



Seems to look ok probably only downer is that the maple veneer on left half is obviously better than right half.https://uploads.tapatalk-cdn.com/20200919/08cfa12488cd9e266aaaf13a94b206da.jpg
https://uploads.tapatalk-cdn.com/20200919/6cb071a4b032a83cc6213a3e44d0439c.jpg
https://uploads.tapatalk-cdn.com/20200919/3e5cc6473b2b5727d76c5238cd245e68.jpg
https://uploads.tapatalk-cdn.com/20200919/762a724803edb3c9de441b8897d082cc.jpg
https://uploads.tapatalk-cdn.com/20200919/593a47db12950e10ab6e72ba7c66c5c0.jpg
https://uploads.tapatalk-cdn.com/20200919/251d2914b67aeb127e2a7c6a530d7f33.jpg
https://uploads.tapatalk-cdn.com/20200919/f5efd78174ca533e5ad20cf5414002ee.jpg


Sent from my iPhone using Tapatalkhttps://uploads.tapatalk-cdn.com/20200919/1a0515551857d54245b2b693d252585c.jpg

GavinPinksterboer
21-09-2020, 09:28 PM
Finished applying the poly to the body , have scraped bindings and cut and polished. Just not sure if I kept applying the poly that will fill
the pores in the timber and make it glassy or it’s ok as it is because I should have grain filled it to begin with?https://uploads.tapatalk-cdn.com/20200921/d847aea4954380476285cefae92c4f2c.jpg
https://uploads.tapatalk-cdn.com/20200921/5cfef035b3ae86668736fb642a9f5760.jpg
https://uploads.tapatalk-cdn.com/20200921/abcc105d55afa4b066b8bbb9be614e45.jpg
https://uploads.tapatalk-cdn.com/20200921/a82c1c334658b8cb236584bbaacf13ad.jpg
https://uploads.tapatalk-cdn.com/20200921/7e6d3f32b3d890ccf69798c66ab05f6c.jpg
https://uploads.tapatalk-cdn.com/20200921/a01be041df9c814f7f4dd4c39f192853.jpg
https://uploads.tapatalk-cdn.com/20200921/a27f3dcf1f27e6ac4c268ff99a895b4d.jpg
https://uploads.tapatalk-cdn.com/20200921/bdfbc6f43174acb9af0014032be9d2b6.jpg
https://uploads.tapatalk-cdn.com/20200921/f0ec185b6c8597f63fe5a59b063cfd59.jpg


Sent from my iPhone using Tapatalk

Ricky
22-09-2020, 02:26 AM
Hi Gavin
Really this thread should be in 'My Build Diary'.

Sorry to hear about your first build. I know it is frustrating when things like that happen but those same things also make us stronger!

I like the colour on your flame maple - very rich looking.
If you want a glass like finish then you will need quite a few more coats before you attempt to cut back and polish but it is worth the effort and time.

Maple is a close grained wood and as such does not need a grain filler. Furthermore, attempting to grain fill figured maple will disguise the flaming and make it appear very plain.

Be careful when sanding veneer. It is supposed to be 0.6mm thick which is very thin anyway but as it is already sanded in the factory it could well be only 0.3mm thick on the horns. Those are the areas that you have already sanded a few times so do not risk anymore sanding.
Several people on here have sanded through in that very area.

Good luck. It is coming along well.

Cheers
Ricky

GavinPinksterboer
22-09-2020, 05:56 AM
Thanks for the advice Ricky , I’ll clean it with wax and grease remover give it a really light scuff over and keep going with poly.

Still learning how to use the forum thing haven’t done this before either hence posting in wrong place

Build one has been revived into satin finish flat black and is looking killer now.

Build 3 arrived yesterday and 4 is on its way.

My 3rd guitar lesson is tomorrow....I can’t even play [emoji23]. But I’m hooked


Sent from my iPhone using Tapatalk

GavinPinksterboer
18-10-2020, 03:02 PM
Take 2. Rubbed back until it was totally flat . Then I’ve Re coated it with cabothane clear gloss. Rub that back again until totally flat with 2500 wet rub. Polished it with Meguiars ultimate compound then coated the whole body with ceramic polymer coated I use on cars. https://uploads.tapatalk-cdn.com/20201018/85ce6cdffbd8d2c5810dabe7ee7b51b3.jpg
https://uploads.tapatalk-cdn.com/20201018/a2d59c9d7bc56eeba52e4b12a5f0b95f.jpg
https://uploads.tapatalk-cdn.com/20201018/bd27dff42e780be6062d517d185fb54e.jpg
https://uploads.tapatalk-cdn.com/20201018/b762c33dbe326ded5fee17c221d3c107.jpg
https://uploads.tapatalk-cdn.com/20201018/995757571ca8200c1175fbc2db34af3c.jpg
https://uploads.tapatalk-cdn.com/20201018/1edfdfb19b2828cd00c857ef918c96b2.jpg


Sent from my iPhone using Tapatalk

Sonic Mountain
18-10-2020, 04:49 PM
Gorgeous! Nice work.

OliSam
20-10-2020, 12:03 PM
Boom!!!!!!!


Sent from my iPhone using Tapatalk

FrankenWashie
29-10-2020, 08:48 PM
Oh my lawdy lawd thats a shiny shiny! Fantastic work!

Joe Garfield
25-03-2021, 11:00 AM
When the finish on your guitar comes out better than the finish on the chrome hardware, you know you're doing something right!

Nice work!