Looking forward to starting my build on the spalted maple ES1-SG spalted maple guitar! Just arrived. Unbelievable how quickly it made it here. Only 5 days to Canada!
Looking forward to starting my build on the spalted maple ES1-SG spalted maple guitar! Just arrived. Unbelievable how quickly it made it here. Only 5 days to Canada!
Good luck and enjoy. 5 days is excellent. Takes longer than that domestically in Aus. Such a good service we get from AusPost nowadays!!
#1 LP1-SS
#2 Non PB Vintage Strat Rebuild
#3 TL1 - Custom
#4 ES-12G (now converted to ES-1)
#5 RC4
#6 STA-1HT
#7 Non PB 52 Tele replica
#8 Coming Soon: 1970's Japanese Les Paul Special Resto.
It may be that your whole purpose in life is simply to serve as a warning to others
Yeah, I really wish I could get things that quickly from AusPost! Enjoy the build, look forward to seeing what you do with it.
#001 (LP-1S) [finished - co-runner up Nov 2018 GOTM]
#002 (WL-1)
#003 (MPL Megacaster - semi scratch build) [finished]
#004 (ST-1 JR - Arachnoid Superhero build) [finished]
#005 (LP jr)
#006 (TL-1A)
Junk shop acoustic refurbs (various)
'The TGS Special'
Welcome to the forum Paul_B
Build #1 - ST-1 - Completed
Build #2 - LP-1SS - Completed
Build #3 - TLA-1R - Completed
Build #4 - SGD-612 - Completed
Build #5 - ES-1G - Completed
Build #6 - STA-1HT | Completed
Build #7 - ST1JR - Completed
Current Build #8 - JBA-4
Build #9 - Semi-scratch build Tele x 2 - Completed
Current Build #10 - PRS-1H
Current Build #11 - AGJR-1 - Completed
Current Build #12 - ATL-1SB
Current Build #13 - GST-1
Current Build #14 - FBM-1
Processing on the build. After much research on options for finishing spalted maple I have elected to simply Tru-Oil the veneer on the top face. I have sourced the Tru-Oil at Lee Valley in Ontario and also found they stock Red Aniline dye that am using for the rest of the wood work (sides/back/neck). I put a few coats of Tru-Oil on the face (after masking off the sides with Fine Line tape to prevent oil bleeding through onto the sides). This protects the top from any accidental staining when I use the Red Aniline dye.
Super happy with the red dye, it produced a beautiful cherry red that will offset the ivory binding and spalted top. Once I figure out how to post a picture I will.
There was a great deal of experimentation on some maple veneer samples I purchased to make sure colour / grain would look good since you only get one chance with stain. I can say that I am not dissapointed!
The first coat of Tru-Oil revealed the grain nicely. As additional coats are added the sheen improves gradually.
. I have finally set the neck. With all of the discussion about different glues I am relieved that I purchased the neck set glue from Pitbull. I had no idea of the controversy and issues with various glues. I want the neck to set and stay put without worrying about creep or weakness of the joint. I admit I would be more comfortable if I could drive a few screws in there to bolster the connection, but I am going to trust the glue supplied by Pitbull. I trust that 24 hours is sufficient to set it up so I can get back to Oiling!
I also made good use of the Copper Tape to create an emblem for the headstock. A razor knife cuts it easily and if you place a printed image over top you can trace the outline and it will mark the tape. Then it is quite simple to cut out the parts you don't want and then peel and stick. Using a roll of masking tape to "iron" it out gets rid of the wrinkles easily. I Tru-Oil over top and eventually it will be buried under the hardshell coating and protected so I can Polish without worry of pulling up the transfer.