Maybe this can work ?
Sharplace Forets HSS Hélicoïdaux Mèche pour Plastique Bois Métal - 1,0 mm à 3,0 mm https://www.amazon.fr/dp/B074QG3B8H/..._E3wrAbDRMGPCF
Maybe this can work ?
Sharplace Forets HSS Hélicoïdaux Mèche pour Plastique Bois Métal - 1,0 mm à 3,0 mm https://www.amazon.fr/dp/B074QG3B8H/..._E3wrAbDRMGPCF
Last edited by Volgar; 14-01-2018 at 07:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Hi Maxence,
the diagram below illustrates the difference. What you had with the bigger set of bits is called a twist drill bit.
The spike helps centre the bit on your drill mark, with a twist bit, the end can wander as the drill begins to rotate before it "bites" into the wood. This can be a big problem when you are drilling by hand held drill.
The set you have shown is a good set, but you must be very careful to punch mark each hole before you begin to drill, and you must be very accurate with the hand held drill.
FrankenLab
Hand crafting guitars, because Death Rays are expensive.
After searching for hours,
I can't find anything on amazon :/
The smallest tip is on the given link! : /
Is there really brad point bit of 1, 1.5, 2mm ? :/
I search on amazon, ebay, aliexpress, and all french big brands of "do-it-yourself" (I don't know if it's the word) stores and nobody sell this ! :/
Last edited by Volgar; 14-01-2018 at 07:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
For the really small sizes, 1 and 1.5mm you'll probably have to use the standard twist drills. From what i have seen the bradpoints start at 2mm, the most common size sets start at 3mm.
When you drill the smallest holes, just make sure you use a nail or a sharp punch to mark the spot to give the drill something to locate the tip and prevent it moving sideways on you.
FrankenLab
Hand crafting guitars, because Death Rays are expensive.
Maybe these can work ?
- 1 & 1.5 mm
- 2 mm
- 3 mm
Last edited by Volgar; 14-01-2018 at 07:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Ok thanks,
Only One drill bit for 1mm is good ?
Last edited by Volgar; 14-01-2018 at 07:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Last edited by Volgar; 14-01-2018 at 07:24 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG
Mooer Black Secrets are phenomenal RAT clones, especially for the price and for their size!
I am a big fan.
And after an ultimate check, here's the list of buyed items :
- 2 mm drill
- 1 & 1.5 mm drill
- 3 mm drill
- Woodfiller
- Straightedge
- Sandpaper
- Fret file
Last edited by Volgar; 14-01-2018 at 07:25 AM. Reason: adding signature
"Isn't funk the most beautiful creation of man?"
- Volgar, 2018
__________________________________________________ __________
#1st build - JMA-1L
#2nd build will certainly be a custom kit close to the GR-1SFG