# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
I agree! Very nice!
Nr 1: Red Widow LP-1MQ (Finished) ->Diary<-
Reviewing the body of this kit I have found a problem I’m not sure how I missed it.
Glue marks I assume are from the binding
Problem is I have already stained the top. It is a splated maple veneer so I assume I can’t sand back and use goof off as I will probably sand through the veneer.
Any advice on how to proceed? I want to try keep the veneer and not have to sand through or spray a solid colour.
All I can think to do is use goof off on the problem areas and because they are around the sides try a black stain to burst? But I’ve never tried that. Any other ideas are welcome.
Sent from my iPhone using Tapatalk
I’ll look into it. Never done a burst before and I don’t have an air gun so it would be a wipe on burst
Sent from my iPhone using Tapatalk
Light sand to the affected areas, add some more stain, let it dry for a few days then delicately add a bit more finish. Can sometimes work or at least minimise the visiblity of what you were trying to disguise. I'd try this before going the burst.
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
Light sand with 240?300? Super scared of going through the veneer
Sent from my iPhone using Tapatalk
Heres a painters trick, lightly sand any top coat you have applied to the affected areas so it dulls or flattens it off, using mabe 400 to 600, always go with the grain. Then get a very small artists brush and using diluted stain exactly paint over the lighter affected areas, if you apply too much gently smudge with a clean cloth until you have the desired blending. Remember if is slightly darker it will look like the grain.
You can apply as many coats as needed to blend the colour and when your satisfied with the results seal it. I use this technique when ive had to do repair work on furniture. Hope this helps.
Last edited by nitroburner1000; 22-06-2018 at 09:10 PM.
Fender electric Fat Strat mim. (Bought)
Maton Electric Acoustic EM325C
Pitbull Guitars ST-1 ( finished) http://www.buildyourownguitar.com.au...ead.php?t=5970
Pitbull Guitars SG-2 ( Finished) http://www.buildyourownguitar.com.au...ead.php?t=6124
Pitbull Guitars JM-1 (Finished. 2018 June GOTM))http://www.buildyourownguitar.com.au...ead.php?t=7150
Pitbull Guitars TL-1 (In production) [url]https://www.buildyourownguitar.com.au/forum/showthread.php?t=8676