Hmmm, melted the top coat and left a crap load of fibres too.
Surprised it didn't eat through your nitrite gloves, something that goof off manages to do after a few minutes of vigorous rubbing.
Hmmm, melted the top coat and left a crap load of fibres too.
Surprised it didn't eat through your nitrite gloves, something that goof off manages to do after a few minutes of vigorous rubbing.
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
Happens to any guitars I have painted with enamel paints. I wont do that anymore
Build #1 - ST-1 - Completed
Build #2 - LP-1SS - Completed
Build #3 - TLA-1R - Completed
Build #4 - SGD-612 - Completed
Build #5 - ES-1G - Completed
Build #6 - STA-1HT | Completed
Build #7 - ST1JR - Completed
Current Build #8 - JBA-4
Build #9 - Semi-scratch build Tele x 2 - Completed
Current Build #10 - PRS-1H
Current Build #11 - AGJR-1 - Completed
Current Build #12 - ATL-1SB
Current Build #13 - GST-1
Current Build #14 - FBM-1
Sorry to (slightly) hijack Robbo's thread but I must ask ...
My first build I brushed and wet sanded 8 coats of acrylic clear and ended up with a HARD attractive finish.
My second I sprayed every different almost empty can of enamel on hand in what was to be multiple prep coats, wet sanded each. It looked so cool it stayed that way and after a weeks went hard HARD and is standing up to use.
My third build is getting close to paint, I had intended spray enamel, I don't mind spending a few extra $$$, what should I be buying?
Hmm, probably going to start an argument here, but I'd be confident in saying that an enamel will be harder than an acrylic finish, and will stand up to abuse better. Enamels tend to soften with contact with hydrocarbons such as fuels and alcohols, but iare otherwise very hard wearing. That's why the goof off stuff was the wrong choice.
Enamel takes longer to go off, and tends to set from the outside in. Acrylic dries from the inside out, and dried much quicker.
Enamels sometimes have a yellowish tinge after time.
The auto stuff you get in Australia car shops for body panels will almost certainly be acrylics.
This info comes from respraying vehicles more than guitars, but I'd say that the same should be true on timber.
I like the Cabots range of polyurethane clear. I have used this over acrylics with no issues, and does make a good hard covering.
Thanks for that comment, keen for further as this stuff is reasonably new to me.
The enamel job referred to started as a knocked about body I found in a garbage bin, filling, sanding then empty whatever pressure pack I had on hand, more sanding, more paint etc etc. End result made me smile so I stopped before final colour coat, it's HARD.
Don't mention the t shirt, my identity must remain a secret ;-)
The pickups came on a loaded pick guard from 920D
https://www.siglermusiconline.com/co...ded-pickguards
they have great stuff but a bit heavy on the $$$'s.
Will it be called The Strato-castaway-er?
Last edited by DarkMark; 25-04-2018 at 09:04 PM.