Trans colors woodgrain

[METAL Rulez 4ever]

http://www.pitbullguitars.com/dingotone/

That would be the best place to start. Keep in mind, Dingobass has been working on some brighter and more vibrant colours, so if you don't see the colour you are interested in there, drop DB an email for more information.

Thank you Zandit, i will check there. Much appreciated.

[wazkelly]

Hi Naim, Having experimented with mixing different Dingo Tone (DT) colours it can be done as evidenced by the light orange colour of my EX-5.

Downsides - at around $25 to $30 per kit it can get a bit expensive and you won't end up using all the stuff as 1 stain kit is more than enough for 1 guitar build. If mixing more than 2 colours the cost factor starts to climb. Not sure where you live and how patient you are as DT does not like to be rushed nor does it work out too good in humid conditions. Theoretically it should take around 3 or 4 months to properly finish a guitar with DT, possibly longer if local climate conditions are not favourable. If you are after a quick, fast result, best to consider something else.

Upsides - environmentally friendly, safe to use indoors or in poorly ventilated areas, has some great colours, supporting an Aussie business, can look stunning once finished properly.

As Woks mentioned a few posts back some timbers will throw a bit of their colour tone into the mix too so what you see on a colour chart and even in the stain container may not be the end result. Also strongly discourage using 0000 steel wool between coats as that stuff tends to break down into very fine particles and even though you think you have got rid of it all invariably some seems to turn up in the last coat just put down. If you must use steel wool suggest you buy a strong magnet to pass over the body after sanding with the stuff to trap and pick up all the loose particles. Clearly I am a fan of wet sanding with a finer grit paper between coats as that does less damage and easier to control.

Hope some of this helps and makes sense too.

[soldier sam]

Wokkaboy
It is an FS1. The stain is Uluru.

The semi-hollow body is made of basswood, with a sensational figure on top, binding front (triple) and back (white) and binding on the two f-holes (white).

Everything still really tacky to touch.

[METAL Rulez 4ever]

Hi Naim, Having experimented with mixing different Dingo Tone (DT) colours it can be done as evidenced by the light orange colour of my EX-5.

Downsides - at around $25 to $30 per kit it can get a bit expensive and you won't end up using all the stuff as 1 stain kit is more than enough for 1 guitar build. If mixing more than 2 colours the cost factor starts to climb. Not sure where you live and how patient you are as DT does not like to be rushed nor does it work out too good in humid conditions. Theoretically it should take around 3 or 4 months to properly finish a guitar with DT, possibly longer if local climate conditions are not favourable. If you are after a quick, fast result, best to consider something else.

Upsides - environmentally friendly, safe to use indoors or in poorly ventilated areas, has some great colours, supporting an Aussie business, can look stunning once finished properly.

As Woks mentioned a few posts back some timbers will throw a bit of their colour tone into the mix too so what you see on a colour chart and even in the stain container may not be the end result. Also strongly discourage using 0000 steel wool between coats as that stuff tends to break down into very fine particles and even though you think you have got rid of it all invariably some seems to turn up in the last coat just put down. If you must use steel wool suggest you buy a strong magnet to pass over the body after sanding with the stuff to trap and pick up all the loose particles. Clearly I am a fan of wet sanding with a finer grit paper between coats as that does less damage and easier to control.

Hope some of this helps and makes sense too.

Hi Waz, yes, very helpful. Thank you so much. I found some Feast and Watson stain, Japan Black and Greenish Oak, so i bought it and will try it. I will also purchase the DingoTone colors also.

[wazkelly]

Not sure IF DT will mix with other stuff as they all have their own unique properties. Best to keep it all in the family so to speak, meaning stick to the same brand or manufacturer to avoid things ending up in tears.

There are always a few exceptions and usually Tru Oil will go down as a top coat over most things if they have been given enough time to dry and cure properly. DT does not like going over the top of anything else other than timber mate used as a grain filler.