Cheers Deddy, or double up for both?
Cheers Deddy, or double up for both?
Stan's LP Build for my Sister: http://www.buildyourownguitar.com.au...ead.php?t=3146
Benson Pickup Strat mod: http://www.buildyourownguitar.com.au...ead.php?t=5229
Epiphone LP headstock fix: http://www.buildyourownguitar.com.au...ead.php?t=3410
Martin Backpacker Repair: http://www.buildyourownguitar.com.au...?t=5038&page=3
'57 Harmony Jazz guitar project: http://www.buildyourownguitar.com.au...ead.php?t=2972
not sure, I didn't want the battery option. Doc could answer that question
Build 19 PSH-1 Kustom
Build 18 HB-4S Kustom
Build 17 WL-1 Kustom
Build 16 TL-1TB Kustom
Build 15 PBG-2-
Build 14 FTD-1
Build 13 RD-1 Kustom
Build 12 DM-1S
Build 11 MKA-2 -
Build 10 Basic strat
Build 9 JM Kustom
Build 8 FV-1G
Build 7 ES-2V
Build 6- Community prototype
Build 5 LP-1LQ
Build 4 ES-5V
Build 3 JR-1
Build 2 GD-1
Build 1 TLA-1
It's actually not that hard at all to wire-up the pedals so that you can power it from either a plugpack adaptor, or a battery, if you're going to do that, I'd suggest getting a couple of black plastic DC-In sockets, or maybe a few of them, I've tried the metal ones that Jaycar sell, but found that they sometimes inadvertently short-out the power plugpack if they are installed in a metal case, the ones you want to use is one of these:
http://www.pedalpartsplus.com/mm5/me...egory_Code=JAC
These sockets have three solder connections on the back of them, one connection is for the centre-pin, another one is for the outer metal-sleeve, and the third one connects to a switch that makes contact with the connection for the centre-pin.
Pedal Parts Plus are a good source of parts for pedals that you can order online, as far as I know, they are the only company that stock the black-plastic DC sockets, there may be some companies, like Altronics in Australia, that stock them, surprisingly, Jaycar Electronics don't seem to stock them at all.
Hope that helps.
They do, but the problem with the ones Jaycar stock is that the mounting-system is metal (the mounting-system happens to be connected to the sleeve connection), and if you mount it in a metal enclosure and wire it up so that it works with a standard 9V DC pedal plugpack (they are wired Centre-Negative as standard), this means that the plugpack adaptor will be shorted-out if the metal enclosure is earthed to prevent hum, I found that out by accident.
Ouch, no wnder they don't show any pics, and yet these (less useful ones) are supposedly plastic. I think I got my last lot from the US.
Scott.
Sorry didn;t get them finished this weekend...maybe next weekend.
Build #1 - ST-1 - Completed
Build #2 - LP-1SS - Completed
Build #3 - TLA-1R - Completed
Build #4 - SGD-612 - Completed
Build #5 - ES-1G - Completed
Build #6 - STA-1HT | Completed
Build #7 - ST1JR - Completed
Current Build #8 - JBA-4
Build #9 - Semi-scratch build Tele x 2 - Completed
Current Build #10 - PRS-1H
Current Build #11 - AGJR-1 - Completed
Current Build #12 - ATL-1SB
Current Build #13 - GST-1
Current Build #14 - FBM-1
G'day Andy, curious to know if you finished the DIY FX pedals over the weekend. Particularly interested in the Overdrive and how you rate the sound as some sound no better than a bunch of bees in a jar. I could be a starter on the Overdrive project but then again for around $50 - $60 there are some damn good factory made things on offer too.
Cheers, Waz.
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
As well as the footswitch, I also can't see a knob for the potentiometer in the kit. Have you got one? Easy to overlook until your final assembly and then it holds you up! Looks like a solid shaft on the pot, so you'll need a knob with a grub screw. As pot shafts come in different sizes, measure its diameter before you buy a knob! (Edit: looks like it should be 6.25mm)
I find it really is best to get your enclosure sorted and drilled before you start wiring things up, as you really want to keep your wire lengths as short as possible (for minimal noise pickup), whilst still giving you enough flexibility to move things around whilst putting it together. Whilst the casing should provide screening from outside interference, any circuit (those designed to add gain especially) allows for the pickup of circuit generated noise by nearby wires. The shorter the length of wire, the less of it there is to pick up noise. Also, it's just easier to fit everything in the box if you haven't got loads of excess wire all coiled up and getting in the way.
(Edit: It does come with an LED - built onto the circuit board so comment about possibly no LED deleted)
Both kit's jack sockets look like the ground connection is connected to the metal fixing screw, so the top half of your case will be nicely grounded as long as this can touch bare metal. You should be able to measure the continuity from the inside of the jack socket to the inside of the case with a multimeter. If there isn't any, then you may need to scrape away at any paint on the inside of the hole for the jack. Some kits come with plastic jack sockets. In this instance you may need to solder an earth wire onto the correct earth tag (or correct size washer) so that it can be connected to earth somewhere on the circuit and the tag mounted so that its kept pressing by a potentiometer or switch onto the metal case. If a potentiometer's body has a connection to earth, this also should provide a good earth connection for the case - but it's worth checking with a multimeter.
If it's a fairly standard cast alloy case, then the bottom cover will simply screw onto the top of the case. Be sure to scrape away any paint around the inner edges of the screw holes in the base plate, so that the screws provide earth continuity to the base plate.
Last edited by Simon Barden; 07-11-2016 at 09:21 PM.