Hey all, if I have gone thick, any tips to be aware of when I give it a light rub with some high grit (DB in the vid says he uses 0000 steel wool which I also have... eg what the finish will do if it isn't dry still?) Cheers.
Hey all, if I have gone thick, any tips to be aware of when I give it a light rub with some high grit (DB in the vid says he uses 0000 steel wool which I also have... eg what the finish will do if it isn't dry still?) Cheers.
Current build (maiden voyage!): PRS - 1TS
Next Build - LP-1S
"Do Not Look Down!!"
If it isn't fully dry, the top layer might be hard but underneath that might be still partially liquid or at least soft. It will smear and look awful.
'As long as there's, you know, sex and drugs, I can do without the rock and roll.'
Thanks... might leave it all another week to be on the safe side!
Current build (maiden voyage!): PRS - 1TS
Next Build - LP-1S
"Do Not Look Down!!"
Good idea. Wouldn't recommend using steel wool as if things are still soft that stuff tends to roll things up into sticky balls of crud and therefore ruin the surface. Only very light fine grade wet sanding seems to be ok and grit needs to be at least 1500 or 2000.
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
Cool thanks... that will make it 3 weeks since applying my 3-4 coats... but that was applying it all in one day... all learning!
Current build (maiden voyage!): PRS - 1TS
Next Build - LP-1S
"Do Not Look Down!!"
Using DT requires lots of patience....... gives you time to start on the electronics or maybe another kit?
# 1 - EX-5 https://goo.gl/fQJMqh
# 2 - EX-1 https://goo.gl/KSY9W9
# 3 - Non PBG Tele https://goo.gl/W14G5g
# 4 - Non PBG J Bass https://goo.gl/FbBaFy
# 5 - TL-1AR GOTM Aug 2017 https://goo.gl/sUh14s
# 6 - MMB-4 Runner-up GOTM Oct 2018https://goo.gl/gvrPkp
# 7 - ES-1 Runner-up GOTM Aug 2018https://goo.gl/T9BEY8
Yeah... I am in no rush at all. I have some other guitars that need some work... always something around to tinker with!
Current build (maiden voyage!): PRS - 1TS
Next Build - LP-1S
"Do Not Look Down!!"
Hey all... I haven't progressed any further since applying the intensifying coats.... need to shape the head stock first.
Not sure I am happy with some of the textures at this point on the neck and head stock... as mentioned above should I rub any areas back very lightly and then apply 1 more coat (lightly this time)?
Cheers all.
Current build (maiden voyage!): PRS - 1TS
Next Build - LP-1S
"Do Not Look Down!!"
sounds good Slayer, might help if you can please post photo's of the area on the neck you aren't happy with
Current Builds and status
scratch end grain pine tele - first clear coat on !
JBA-4 - assembled - final tweaks
Telemonster double scale tele - finish tobacco burst on body and sand neck
Completed builds
scratch oak.rose gum Jazzmaster - assembled needs setup
MK-2 Mosrite - assembled - play in
Ash tele with Baritone neck - neck pup wiring tweaks and play in
Shall do! Cheers.
Current build (maiden voyage!): PRS - 1TS
Next Build - LP-1S
"Do Not Look Down!!"